湿法分层缠绕T700/环氧复合材料微波固化工艺及性能

doi:10.19936/j.cnki.2096-8000.20211228.014

摘要/Abstract

摘要： 针对大厚度固体火箭发动机壳体制造周期长的缺点,本文提出分层缠绕微波预固化工艺。以固化度为依据,结合壳体缠绕规律及微波吸收效率,筛选出[90°₂/±20°]的分层缠绕基元。分层缠绕中需经多次微波辐射,考虑热传导或弱微波效应对已缠绕层固化度的影响,制定出升温速率为5 ℃/min、由室温升至90 ℃的微波预固化工艺,后处理采用热固化:160 ℃保温1 h。在微波固化试样制备时间(均不考虑降温时间)比热固化缩短近一半的情况下,T700碳纤维复合材料微波固化与热固化试样力学性能基本一致:微波固化层合板拉伸强度为1.84 GPa,热固化层合板拉伸强度为1.76 GPa;微波固化层合板弯曲强度为1.20 GPa,热固化层合板弯曲强度为1.17 GPa;微波固化NOL环拉伸强度为2.94 GPa,热固化NOL环拉伸强度为3.08 GPa;微波固化NOL环层间剪切强度为76.1 MPa,热固化NOL环层间剪切强度为75.6 MPa。扫描电镜照片表明,两种固化方式下纤维-基体界面结合良好。由于微波固化不依赖于热传导或热对流,因此可以在较短的时间内达到与热固化试样相当的力学性能。

关键词: 固体火箭发动机壳体, 碳纤维复合材料, 湿法分层缠绕工艺, 微波固化, 热固化, 力学性能

Abstract: In this paper, the rapid manufacturing of large-size solid rocket motor shell is the research background. Aiming at the problems of long curing cycle and high production cost in traditional heat curing, a layered microwave pre-curing process is proposed to shorten the manufacturing cycle and maintain excellent performance. With the help of differential scanning calorimeter, based on the curing degree, combined with the shell winding law and microwave absorption efficiency, the layered winding element of [90°₂/±20°] was selected. Considering the influence of heat conduction and microwave effect on the curing degree of the wound layer, a microwave pre-curing process with heating rate of 5 ℃/min and rising from room temperature to 90 ℃ was determined. The post-treatment was heat curing by holding at 160 ℃ for 1 h. Microwave curing and heat curing composite laminates and NOL rings were prepared. When the preparation time of samples cured by microwave (regardless of cooling time) is nearly half shorter than that of samples cured by heat, the mechanical properties of samples cured by microwave and heat are basically the same. Because of the bulk heating characteristics of microwave curing, it can achieve the mechanical properties equivalent to that of the heat cured samples in a short time.

Key words: solid rocket motor shell, carbon fiber composites, wet layered winding, microwave curing, heat curing, mechanical properties

中图分类号:

TB332

李梦颖, 肖军, 还大军, 王兴邦, 杨潇, 焦洋. 湿法分层缠绕T700/环氧复合材料微波固化工艺及性能[J]. 复合材料科学与工程, 2021, 0(12): 89-94.

LI Meng-ying, XIAO Jun, HUAN Da-jun, WANG Xing-bang, YANG Xiao, JIAO Yang. Microwave curing process and properties of T700/epoxy composites by wet filament lamination winding[J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(12): 89-94.

参考文献

[1] ZHANG L, CHANG X L, ZHANG Y H, et al. Large strain detection of SRM composite shell based on fiber Bragg grating sensor[J]. Photonic Sensors, 2017, 7(4): 350-356.
[2] 王秀萍. 美国固体火箭发动机的发展及其在机载战术导弹上的应用[J]. 航空兵器, 2016(3): 14-17.
[3] 崔红, 王晓洁, 闫联生. 固体火箭发动机复合材料与工艺[M]. 西安: 西北工业大学出版社, 2016: 1-7.
[4] YIN J J, CHANG F, LI S L, et al. Lightning strike ablation damage influence factors analysis of carbon fiber/epoxy composite based on coupled electrical-thermal simulation[J]. Applied Composite Materials, 2017, 24(5): 1089-1106.
[5] ATAS A, GAUTAM M, SOUTIS C, et al. Bolted joints in three axially braided carbon fiber/epoxy textile composites with moulded-in and drilled fastener holes[J]. Applied Composite Materials, 2017, 24(2): 449-460.
[6] PARK S Y, CHOI C H, CHOI W J, et al. A comparison of the properties of carbon fiber epoxy composites produced by non-autoclave with vacuum bag only prepreg and autoclave process[J]. Applied Composite Materials, 2019, 26(1): 187-204.
[7] LI Y G, CHENG L B, ZHOU J. Curing multidirectional carbon fiber reinforced polymer composites with indirect microwave heating[J]. The International Journal of Advanced Manufacturing Technology, 2018, 97: 1137-1147.
[8] ZOLLINGER M, BRAUCHLI-THEOTOKIS J, GUTTECK-AMSLER U, et al. Conventional and microwave curing process of epoxy systems: Kinetic analysis and characterization[J]. Microwave and Optical Technology Letters, 2010, 51(11): 2777-2783.
[9] XU X H, WANG X Q, WEI R, et al. Effect of microwave curing process on the flexural strength and interlaminar shear strength of carbon fiber/bismaleimide composites[J]. Composites Science and Technology, 2016, 123(FEB.8): 10-16.
[10] SHIMAMOTO D, TOMINAGA Y, HOTTA Y. Effect of microwave irradiation on carbon fiber/epoxy resin composite fabricated by vacuum assisted resin transfer molding[J]. Advanced Composite Materials, 2016, 25(s1): 71-79.
[11] KWAK M, ROBINSON P, BISMARCK A, et al. Microwave curing of carbon-epoxy composites: Penetration depth and material characterization[J]. Composites Part A: Applied Science and Manufacturing, 2015, 75: 18-27.
[12] LI N Y, LI Y G, HAO X P, et al. A comparative experiment for the analysis of microwave and thermal process induced strains of carbon fiber/bismaleimide composite materials[J]. Composites Science and Technology, 2015, 106(106): 15-19.
[13] LI Y G, HANG X, LI N Y, et al. A temperature distribution prediction model of carbon fiber reinforced composites during microwave cure[J]. Journal of Materials Processing Technology, 2016, 230: 280-287.
[14] XU X H, WANG X Q, CAI Q, et al. Improvement of the compressive strength of carbon fiber/epoxy composites via microwave curing[J]. Journal of Materials Science and Technology, 2016, 32: 226-232.
[15] LI N Y, LI Y G, JELONNEK J, et al. A new process control method for microwave curing of carbon fiber reinforced composites in aerospace applications[J]. Composites Part B: Engineering, 2017, 122: 61-70.
[16] KWAK M, ROBINSON P, BISMARCK A, et al. Curing of composite materials using the recently developed Hephaistos microwave[C]//Korea: 18th International Conferences on Composite Materials. 2011: 1-6.
[17] MA R L, CHANG X L, ZHANG X J, et al. Effect of curing method on mechanical and morphological properties of carbon fiber epoxy composites for solid rocket motor[J]. Polymer Composites, 2015, 36(9): 1703-1711.
[18] CHINEDUM O M, LI D, LIN M F, et al. Accelerated microwave curing of fiber-reinforced thermoset polymer composites for structural applications: A review of scientific challenges[J]. Composites Part A: Applied Science and Manufacturing, 2018, 115: 88-103.
[19] LEE W I, SPRINGER G S. Interaction of electromagnetic radiation with organic matrix composites[J]. Journal of Composite Materials, 1984, 18(4): 357-386.
[20] 王晓红, 刘俊能. 碳纤维复合材料的微波反射特性研究[J]. 功能材料, 1999, 30(4): 387-388.
[21] 杭翔. 飞机复合材料微波固化工艺研究[D]. 南京: 南京航空航天大学, 2015: 51.