混杂碳/玻纤维复合材料自行车轮辋的铺层优化分析及抗疲劳验证

doi:10.19936/j.cnki.2096-8000.20231128.009

复合材料科学与工程 ›› 2023, Vol. 0 ›› Issue (11): 70-77.DOI: 10.19936/j.cnki.2096-8000.20231128.009

混杂碳/玻纤维复合材料自行车轮辋的铺层优化分析及抗疲劳验证

周勇军¹, 邱宇鸿², 李红周^2*

1.闽南科技学院,泉州 362200;
2.福建师范大学环境与资源学院碳中和现代产业学院,福州 350007

收稿日期:2022-10-18 出版日期:2023-11-28 发布日期:2023-12-14
通讯作者: 李红周(1978—),男,教授,博士,主要从事复合材料的力学性能优化方面的研究,lihongzhou@fjnu.edu.cn。
作者简介:周勇军(1971—),男,副教授,硕士,主要从事复合材料的力学性能有限元仿真方面的研究。
基金资助:
福建省自然科学基金(2021J01198);泉州市科技计划项目(2022C008R)

Optimal layup analysis and anti-fatigue verification of bicycle rim with inter-ply hybrid carbon/glass fiber reinforced composites

ZHOU Yongjun¹, QIU Yuhong², LI Hongzhou^2*

1. Minnan Science and Technology University, Quanzhou 362200, China;
2. College of Carbon Neutral Modern Industry, College of Environmental and Resources, Fujian Normal University, Fuzhou 350007, China

Received:2022-10-18 Online:2023-11-28 Published:2023-12-14

摘要/Abstract

摘要： 对碳纤维/玻璃纤维层间混杂复合材料自行车轮辋进行数值优化分析,能够设计出具有价格适中、安全性能高、耐疲劳等特点的自行车轮辋。借助有限元分析对自行车轮辋模型进行服役状态下的力学行为模拟,能够为试验研究提供相对可靠的方案,减少试验过程中不必要的原料浪费,从而降低整个复合材料轮辋的设计和制备成本。本文通过ABAQUS软件构建了自行车轮辋模型,通过调整碳纤维预浸布铺层和玻璃纤维预浸布铺层的顺序、各铺层角度比例和顺序,计算轮辋在服役状态下的力学性能,通过比较各方案得到较优的设计方案。5万次加速疲劳测试结果表明:采用优化后的自行车轮辋侧壁铺层方案及凸缘铺层方案指导复合材料轮辋的制备,可以显著提高复合材料自行车轮辋的抗疲劳能力。

关键词: 自行车轮辋, 层间混杂纤维复合材料, 铺层优化设计, 有限元分析, 加速疲劳测试

Abstract: Bicycle rim with moderate cost, high safety performance, anti-fatigue and other characteristics can be designed through numerically optimal analysis of bicycle rim with inter-ply carbon/glass hybrid fiber reinforced polymer composites. To simulate the behavior of the composite bicycle rim in service by finite element analysis, it can provide relatively reliable scheme for experiments and minimize the waste of the raw material in experiments, and reduce the cost of design and preparation of the composite rim. In this paper, a bicycle rim model was constructed by adjusting the order of carbon fiber prepreg and glass fiber prepreg, the proportion and order of each ply orientation, and the mechanical properties of the rim in service were calculated by the software ABAQUS. The optimal layup scheme was obtained by comparing each scheme of the simulated composite rim in service. The results of accelerated fatigue test (50 000 times) demonstrate that selecting the optimal lay up scheme of rim sidewall and rim bead to make the composite bicycle rim can significantly improve its anti-fatigue capability.

Key words: bicycle rim, inter-ply hybrid fiber reinforced composite, optimal lay up design, finite element analysis, accelerated fatigue test

中图分类号:

TB332

周勇军, 邱宇鸿, 李红周. 混杂碳/玻纤维复合材料自行车轮辋的铺层优化分析及抗疲劳验证[J]. 复合材料科学与工程, 2023, 0(11): 70-77.

ZHOU Yongjun, QIU Yuhong, LI Hongzhou. Optimal layup analysis and anti-fatigue verification of bicycle rim with inter-ply hybrid carbon/glass fiber reinforced composites[J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(11): 70-77.

参考文献

[1] ZHANG J, CHAISOMBAT K, HE S, et al. Hybrid composite laminates reinforced with glass/carbon woven fabrics for lightweight load bearing structures[J]. Materials & Design, 2012, 36: 75-80.
[2] CZEL G. Development of bi-directional pseudo-ductile glass/carbon-epoxy hybrid composites for improved safety in structural applications[J]. Composites Part B: Engineering, 2021, 231: 109546.
[3] BUNEA M, CIRCIUMARU A, BUCIUMEANU M, et al. Low velocity impact response of fabric reinforced hybrid composites with stratified filled epoxy matrix[J]. Composites Science and Technology, 2019, 169: 242-248.
[4] 郭小锋,齐剑峰,黄鑫祥. 玻碳混杂低风速风电叶片结构优化及性能分析[J]. 复合材料科学与工程, 2020(6): 25-29.
[5] PENG X, GUO Y L, LI J Q, et al. Multiple objective optimization design of hybrid composite structures considering multiple-scale uncertainties[J]. Composite Structures, 2022, 292: 115658.
[6] RIBEIRO S L M, GARCIA C T, DONADON M V, et al. The impact behaviour of hybrid fibre-particle composites based on a full factorial design[J]. Materials Today Communications, 2022, 31: 103459.
[7] 赵迅鹏,孙双双,王洋,等. 湿热环境下玻/碳纤维混杂复合材料弯曲强度的宏观力学分析[J]. 复合材料科学与工程, 2022(9): 41-47.
[8] 仇刚, 朱福先, 朱兴民, 等. 碳/玻混杂复合材料层合板单钉螺栓连接孔边应力分析[J]. 复合材料科学与工程, 2023(3): 18-26.
[9] 周越松, 梁森, 王得盼, 等. 层间混杂铺层复合材料装甲抗侵彻性能研究[J]. 化工新型材料, 2022, 50(10): 118-123.
[10] 王海雷, 段跃新, 王维维, 等. 玻璃纤维与碳纤维混杂复合材料的拉伸及低速冲击性能研究[J]. 复合材料科学与工程, 2021(2): 102-109.
[11] 许经纬, 顾嫒娟. 碳玻混杂纤维增强复合材料的拉-拉疲劳性能的研究[J]. 复合材料科学与工程, 2020(4): 39-45.
[12] DASARI S, SAURABH S, PRUSTY R K. Temperature and loading speed sensitivity of glass/carbon inter-ply hybrid polymer composites on tensile loading[J]. Journal of Applied Polymer Science, 2020, 138(9): e49928.
[13] AZLIN M N M, SAPUAN S M, ZUHRI M Y M, et al. Effect of stacking sequence and fiber content on mechanical and morphological properties of woven kenaf/polyester fiber reinforced polylactic acid (PLA) hybrid laminated composites[J]. Journal of Materials Research and Technology-JMR&T, 2022, 16: 1190-1201.
[14] MOHANAVEL V, KUMAR S S, VAIRAMUTHU J, et al. Influence of stacking sequence and fiber content on the mechanical properties of natural and synthetic fibers reinforced penta-layered hybrid composites[J]. Journal of Natural Fibers, 2022, 19(13): 5258-5270.
[15] WANG T T, SONG B, QIAO K, et al. Influence of the hybrid ratio and stacking sequence on mechanical and damping properties of hybrid composites[J]. Polymer Composites, 2019, 40(6): 2368-2380.
[16] GEMI L. Investigation of the effect of stacking sequence on low velocity impact response and damage formation in hybrid composite pipes under internal pressure. A comparative study[J]. Composites Part B: Engineering, 2018, 153: 217-232.
[17] CAMINERO M A, RODRIGUEZ G P, MUNOZ V. Effect of stacking sequence on charpy impact and flexural damage behavior of composite laminates[J]. Composite Structures, 2016, 136: 347-357.
[18] 刘宇宸, 花军, 宁礼佳, 等. 碳/玻璃纤维混编复合材料压簧制作方法及实验研究[J]. 复合材料科学与工程, 2021(2): 43-48.
[19] JIANG H Y, REN Y R, LIU Z H, et al. Low-velocity impact resistance behaviors of bio-inspired helicoidal composite laminates with non-linear rotation angle based layups[J]. Composite Structures, 2019, 214: 463-475.
[20] FOTOUHI M, JALALVAND M, WISNOM M R. High performance quasi-isotropic thin-ply carbon/glass hybrid composites with pseudo-ductile behaviour in all fibre orientations[J]. Composites Science and Technology, 2017, 152: 101-110.
[21] FULLER J D, WISNOM M R. Pseudo-ductility and damage suppression in thin ply CFRP angle-ply laminates[J]. Composites Part A: Applied Science and Manufacturing, 2015, 69: 64-71.

混杂碳/玻纤维复合材料自行车轮辋的铺层优化分析及抗疲劳验证

Optimal layup analysis and anti-fatigue verification of bicycle rim with inter-ply hybrid carbon/glass fiber reinforced composites

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	赵艺, 赵刚, 范欣愉, 闫忠伟, 葛亚琼, 徐剑. 基于渐进损伤模型的热固性复合材料电阻焊接头强度的尺寸效应研究[J]. 复合材料科学与工程, 2024, 0(2): 45-51.
[2]	张弘强, 陈栋, 李成. CFRP层合板双面挖补补片设计及性能分析[J]. 复合材料科学与工程, 2024, 0(2): 52-58.
[3]	余章杰, 张琪, 蔡登安, 戴征征, 周光明. 碳纤维/环氧树脂复合材料-金属连接结构面外拉伸失效机制[J]. 复合材料科学与工程, 2023, 0(7): 5-12.
[4]	张学文, 王继辉, 陈宏达, 倪爱清. 单向增强热塑性复合材料热冲压成型仿真与优化[J]. 复合材料科学与工程, 2023, 0(6): 104-114.
[5]	沈昊辰, 牛波, 张琪凯, 郝晶莹, 张亚运, 龙东辉. 2.5D石英纤维增强纳米孔酚醛树脂基复合材料的力学和传热性能[J]. 复合材料科学与工程, 2023, 0(4): 5-13.
[6]	辛志博, 朱彦松, 段玉岗, 王奔, 黄志文, 王宏晓, 明越科. 直升机复合材料油箱密封结构分析与试验研究[J]. 复合材料科学与工程, 2023, 0(4): 87-93.
[7]	张锦光, 邓伟, 杨桢, 邱浩, 文湘隆. 纤维增强复合材料叶轮对风机振动特性的影响研究[J]. 复合材料科学与工程, 2023, 0(3): 53-58.
[8]	张智梅, 杨旸. 外贴预应力CFRP布加固钢筋混凝土梁抗弯疲劳性能有限元分析[J]. 复合材料科学与工程, 2023, 0(2): 44-53.
[9]	许良, 胡鸿铭, 周松, 宋万万. 两次冲击距离对CFRP层合板冲击损伤和剩余压缩强度的影响[J]. 复合材料科学与工程, 2023, 0(12): 12-18.
[10]	刘嘉, 吴江, 张夫恩, 吴道明. 复合材料水平尾翼的后梁铺层优化研究[J]. 复合材料科学与工程, 2023, 0(11): 78-83.
[11]	元振毅, 魏方见, 孔令飞, 杨振朝, 同新星, 李言. 模具-复合材料相互作用的复合材料固化变形仿真方法研究[J]. 复合材料科学与工程, 2023, 0(10): 10-16.
[12]	马国瑞, 梁森, 杨功先. 双层阻尼薄膜夹嵌复合材料梁的动力学性能[J]. 复合材料科学与工程, 2022, 0(9): 11-22.
[13]	程文礼, 蒋婷, 万喜伟, 刘晓东, 叶宏军, 关志东. 复合材料加筋壁板不同工艺固化变形试验及模拟[J]. 复合材料科学与工程, 2022, 0(9): 90-96.
[14]	刘志, 张彬, 赵微微, 张勇. 聚氨酯复合材料步行板结构设计及力学性能研究[J]. 复合材料科学与工程, 2022, 0(7): 103-106.
[15]	杨智勇, 刘清念, 孙建波, 解永杰, 左小彪, 张建宝. 铺层角度偏差对曲面复合材料层合板形面轮廓的影响分析[J]. 复合材料科学与工程, 2022, 0(6): 17-26.