T800碳纤维复合材料多钉连接层压板钉载分布及有限元计算

复合材料科学与工程 ›› 2015, Vol. 0 ›› Issue (1): 28-32.

T800碳纤维复合材料多钉连接层压板钉载分布及有限元计算

张明星

上海飞机设计研究院,上海201210

收稿日期:2013-04-18 出版日期:2015-01-28 发布日期:2021-09-14
作者简介:张明星(1982-),男,博士,主要从事纤维增强复合材料研究,schoolstar1982@hotmail.com

LOAD DISTRIBUTION AND FINITE ELEMENT ANALYSIS OF MULTI-FASTENER JOINTS T800 COMPOSITE LAMINATES

ZHANG Ming-xing

Shanghai Aircraft Design and Research Institute, Shanghai 201210, China

Received:2013-04-18 Online:2015-01-28 Published:2021-09-14

摘要/Abstract

摘要： 通过对T800碳纤维预浸料复合材料层压板多钉连接试验件进行轴向拉伸测试,测得了整个试验件的载荷-位移曲线和每一个钉孔附近的应变-载荷曲线。试验结果表明,首末两排钉承担载荷最大,中间排钉载荷最小;试件的破坏都是发生在第一排钉附近;破坏模式主要为钉孔挤压和层压板拉伸破坏;建立了相应的有限元模型,模拟结果和试验结果的一致说明了有限元模型的合理性。

关键词: 多钉连接, 钉载分布, 应变, 破坏模式, 有限元分析

Abstract: Tension test were performed on multi-fastener joints composite laminates samples produced with T800 carbon fiber prepreg. Load-displacement curves of whole composite samples under axial tensile load were obtained, and strain-load curves were available through the strain flowers around the holes. The results show that the first and last rows fasteners carry the most load and the middle ones take the least load. The samples break on the area near the first row fasteners. The failure modes mainly are squeezed fastener hole and tensile failure. One finite element analysis model is established and verified with the high agreement between simulated and experimental results.

Key words: multi-fastener joints, load distribution, strain, failure mode, finite element analysis

中图分类号:

TB332

张明星. T800碳纤维复合材料多钉连接层压板钉载分布及有限元计算[J]. 复合材料科学与工程, 2015, 0(1): 28-32.

ZHANG Ming-xing. LOAD DISTRIBUTION AND FINITE ELEMENT ANALYSIS OF MULTI-FASTENER JOINTS T800 COMPOSITE LAMINATES[J]. COMPOSITES SCIENCE AND ENGINEERING, 2015, 0(1): 28-32.

参考文献

[1] Shoumei Wang, Yao xin han. Finite element analysis for load distribution of multi-fastener joints [J]. Composite material, 1988, 22(2): 125-135.
[2] De-Jong Th. Stress around pin-load hole in elastically orthotropic or isotropic plates [J]. Composite material, 1977, 11(3): 313-331.
[3] 李成, 郑艳萍. 机械连接结构中含圆孔复合材料板的盈利计算及仿真分析[J]. 玻璃钢/复合材料, 2007, (3): 3-5.
[4] 刘达, 刘一兵, 魏春龙, 贾普荣. 碳纤维增强复合材料层板机械连接的拉脱强度[J]. 强度与环境, 1996, (2): 1-3.
[5] 姜云鹏, 岳珠峰. 复合材料层压板螺栓连接失效的数值模拟[J]. 复合材料学报, 2005, 22(4): 178-181.
[6] 陈绍杰. 复合材料设计手册[M]. 北京: 航空工业出版社, 1990.
[7] 张爽, 王栋, 郦正能, 寇长河, 章怡宁. 基于ANSYS的复合材料层合板单钉连接件参数化结构仿真[J]. 航空学报, 2006, 27(6): 1088-1091.
[8] Tserpes K I , Labeas G, Papanikos P, et al. Strength prediction of bolted joint s in graphite/epoxy composite laminates[J]. Composites Part B: Engineering, 2002, 33(7): 521-529.
[9] Mahmood M S, Larry B L. Effects of materials nonlinearity on the three-dimensional stress state of pin-loaded composite laminates[J]. Journal of Composite Materials, 1996, 30 (7): 839-861.
[10] Kai H. Failure analysis of bolted composite joints exhibiting in-plane failure modes[J]. Journal of Composite Materials, 1996, 30 (3): 358-383.
[11] Tong L, Steven G P. Analysis and design of structural bonded joints[M]. Boston: Kluwer Academic, 1999.
[12] Jan y E, Shenoi R A. Performance of butt strap joints for marine applications[J]. International Journal of Adhesion&Adhesives, 2006, (26): 162-176.
[13] Zou G P, Shahin K, Tahefi F. An analytical solution for the analysis of symmetric composite adhesively bonded joints[J]. Composite Structures, 2004,(65): 499-510.
[14] 尹星研, 冯振宇, 卢翔. 基于MSC.Nastran的无人机复合材料机翼有限元分析[J]. 玻璃钢/复合材料, 2010, (1): 3-4.
[15] 李玮, 段成红, 吴祥. 碳纤维复合材料强度的有限元模拟[J]. 玻璃钢/复合材料, 2011, (1): 21-24.
[16] 王清远, 袁祥明, 等. 损伤金属结构件复合材料粘贴修补[J]. 玻璃钢/复合材料, 2003, (6): 41-44.
[17] 殷强, 曾竟成, 等. 双向受载裂纹板的复合材料补片胶接修补[J]. 玻璃钢/复合材料, 2005, (6): 38-41.