树脂基复合材料内外协同固化工艺仿真与分析

复合材料科学与工程 ›› 2015, Vol. 0 ›› Issue (7): 12-17.

树脂基复合材料内外协同固化工艺仿真与分析

许家忠, 李爽^*, 乔明, 尤波

哈尔滨理工大学,黑龙江哈尔滨 150080

收稿日期:2015-02-12 出版日期:2015-07-28 发布日期:2021-09-13
通讯作者: 李爽(1989-),女,硕士,主要从事复合材料固化模拟方面的研究工作,997407131@qq.com。
作者简介:许家忠(1977-),男,博士,主要从事复合材料固化方面的研究工作。
基金资助:
黑龙江省自然科学基金(E201301)

RESIN MATRIX COMPOSITES SIMULATION AND ANALYSIS OF INTERNAL-EXTERNAL COORDINATION CURING

XU Jia-zhong, LI Shuang^*, QIAO Ming, YOU Bo

Harbin University of Science and Technology, Harbin 150080, China

Received:2015-02-12 Online:2015-07-28 Published:2021-09-13

摘要/Abstract

摘要： 在采用传统内固化工艺对厚壁壳体成型时,内层温度往往不足以满足其固化要求或者加热时间过长,因此通常采用多次缠绕多次固化的成型工艺,耗能高、效率低,不但大大提高了成本,也难以保证产品质量。因此本文提出了内外协同固化新工艺并介绍其原理,建立纤维树脂复合材料厚壁壳体内外协同固化过程的传热模型和固化动力学模型,通过有限元软件ANSYS和APDL语言开发内外协同固化过程数值模拟程序,实现了厚壁壳体内外协同固化过程中温度和固化度的分布及其变化规律的数值模拟研究。对新工艺的数值模拟结果表明,随着外温和预热温度的不断增大,中心节点的温度、固化度和应变波动较大;厚壁壳体内外协同固化的时间很短,是传统固化时间的1/3。

关键词: 纤维复合材料厚壁壳体, 内外协同固化, 数值模拟

Abstract: In the traditional curing process of thick-walled shell winding, the inner temperature is often not enough to meet the requirement of its curing or time is too long, so it usually adopt molding process of many winding and much curing, high energy, low efficiency, which not only has greatly increased the cost, and as a result of layered of curing resin cross-linking, so difficult to guarantee the quality of the product. So the new internal-external coordination curing process is advanced in this paper and its principles are introduced. Two mathematical models including heat conduction model and cure kinetics model of fiber composite thick-walled shell of the internal-external coordination curing process are built. The finite element software ANSYS and APDL language are used to develop numerical simulation procedure of the process, the numerical simulation program of the internal-external coordination curing process is developed to study the distribution and the variation of temperature and curing degree. The numerical simulation of the new process shows that with external heating source temperature and preheating temperature, changing curve of temperature, curing and strain of center node is increased, and walled housing internal-external coordination curing time is shorted to 1/3 of the curing time of traditional method.

Key words: fiber composite thick-walled shell, the internal-external coordination curing, numerical simulation

中图分类号:

TB332

许家忠, 李爽, 乔明, 尤波. 树脂基复合材料内外协同固化工艺仿真与分析[J]. 复合材料科学与工程, 2015, 0(7): 12-17.

XU Jia-zhong, LI Shuang, QIAO Ming, YOU Bo. RESIN MATRIX COMPOSITES SIMULATION AND ANALYSIS OF INTERNAL-EXTERNAL COORDINATION CURING[J]. COMPOSITES SCIENCE AND ENGINEERING, 2015, 0(7): 12-17.

参考文献

[1] Zu L, Koussios S, Beukers A. Design of filament-wound isotensoid pressure vessels with unequal polar openings[J]. Composite Structures, 2010, 92(9): 2307-2313.
[2] Zu L. Stability of fiber trajectories for winding toroidal pressure vessels[J]. Composite Structures, 2012, 94(5): 1855-1860.
[3] Xu J Z, Wang X Y, Qiao M, et al. The numerical simulation research of internal curing process for fiber winding composite shell[J]. Polymer and Polymer Composites, 2011, 19(4-5): 319-326.
[4] Xu J Z, Qiao M, You B, et al. Research on heated-mandrel winding process for resin-matrix composite shells[J]. Journal of Reinforced Plastics and Composites, 2012, 31(9): 605-620.
[5] Xu J Z, Qiao M, You B, et al. Simulation and optimization of mandrel-heating process for composite shells using internal heat-curing method[J]. Journal of Reinforced Plastics and Composites, 2012, 31(3): 133-143.
[6] Kim J, Moon T J M, Howell J R. Transient thermal modeling of in-Situ curing during tape winding of composite cylinders[J]. Journal of Heat Transfer, 2003, 125(1): 137-146.
[7] Sorrentino L, Tersigni L. A method for cure process design of thick composite components manufactured by closed die technology[J]. Applied Composite Materials, 2012, 19(1): 31-45.
[8] Abdel-Hady F. Filament winding of revolution structures[J]. Journal of Reinforced Plastics and Composites, 2005, 24(8): 855-868.
[9] KIM C, White S R. Continuous curing and induced thermal stresses of a thick filament wound composite cylinder[J]. Journal of Reinforced Plastics and Composites, 2001, 20: 166.
[10] Costa M L, Botelho E C, Rezende M C. Monitoring of cure kinetic prepreg and cure cycle modeling[J]. Journal of Materials Science, 2006, 41(13): 4349-4356.
[11] YAN X Q. Finite element simulation of cure of thick composite: Formulations and validation verification[J]. Journal of Reinforced Plastics and Composites, 2008, 27(4): 339-355.
[12] 寇哲君, 戴棣, 曹正华. 复合材料结构固化变形预测[J]. 材料工程, 2007, 1: 225-227.
[13] 李辰砂, 冷劲松, 王殿富, 等. 纤维缠绕圆筒复合材料固化成型过程机理模型[J]. 纤维复合材料, 2000, (4): 19-28.
[14] Kim Y K, White S R. Viscoelastic analysis of processing- induced residual stresses in thick composite laminates[J]. Mechanics of Composite Materials and Structures, 1997, (4): 361-387.
[15] Antonucci V, Giordano M, Hsiao K, et al. A methodology to reduce thermal gradients due to the exothermic reactions in composites processing[J]. International journal of heat and mass transfer, 2002, (45): 1675-1684.