一种RTM用耐烧蚀改性酚醛树脂性能研究

复合材料科学与工程 ›› 2015, Vol. 0 ›› Issue (7): 18-21.

一种RTM用耐烧蚀改性酚醛树脂性能研究

李婷^*, 刘建军, 杨学军, 赵文斌

西安航天复合材料研究所,西安 710025

收稿日期:2015-02-03 出版日期:2015-07-28 发布日期:2021-09-13
作者简介:李婷(1987-),女,硕士研究生,主要从事树脂基复合材料方面的研究。

RESEARCH ON PROPERTIES OF A ABLATIVE MODIFIED PHENOLIC RESIN

LI Ting^*, LIU Jian-jun, YANG Xue-jun, ZHAO Wen-bin

Xi'an Aerospace Composite Materials Research Institute, Xi'an 710025, China

Received:2015-02-03 Online:2015-07-28 Published:2021-09-13

摘要/Abstract

摘要： 对一种新型改性酚醛树脂的粘度特性、耐热性和耐烧蚀性能及其复合材料的性能进行了研究,得出该树脂体系的粘度在60~120℃的范围内均小于800mPa·s,且在70℃、80℃时工艺适用期大于150min;其玻璃化温度Tg为253℃,氮气气氛800℃残炭率可达到67.1%,质量烧蚀率和线烧蚀率分别为0.0766g/s、0.119mm/s;RTM成型碳纤维增强改性酚醛树脂复合材料的层间剪切强度和轴向压缩强度分别可达39.3MPa和177MPa,氧-乙炔烧蚀的线烧蚀率和质量烧蚀率分别为0.044mm/s、0.0762g/s。结果表明,该种树脂体系具有粘度低、工艺适用期长以及良好的耐热性和耐烧蚀性能,能很好地满足RTM工艺的要求,且其碳纤维针刺复合材料具有作为耐烧蚀材料的潜质。

关键词: 改性酚醛树脂, RTM工艺, 粘度特性, 烧蚀性能

Abstract: In this paper, a modified phenolic resin was studied, including viscosity property, heat resistance and ablative property. It is found that the viscosity of resin system is lower than 800mPa·s in the range of 60~120℃, process applicable period is longer than 150 mins at 70℃ and 80℃. The glass transition temperature is 253℃, carbon residue rate at 800℃ is 67.1% in the Nitrogen atmosphere, quality ablation rate and linear ablation rate are 0.0766g/s and 0.119mm/s. Carbon fiber needling preform reinforced the modified phenolic resin composite was made by RTM, its interlayer shear strength and axial compressive strength are 39.3MPa and 177MPa, respectively. The linear ablation rate and quality ablation rate are 0.044mm/s and 0.0762g/s. Experimental results show that this modified phenolic resin system, which has low viscosity, long process applicable period, good heat resistance and ablative property, can meet the requirement of RTM process well, and its carbon fiber needling perform composite has the potential of being used as ablation resistant material.

Key words: modified phenolic resin, RTM process, viscosity property, ablative property

中图分类号:

李婷, 刘建军, 杨学军, 赵文斌. 一种RTM用耐烧蚀改性酚醛树脂性能研究[J]. 复合材料科学与工程, 2015, 0(7): 18-21.

LI Ting, LIU Jian-jun, YANG Xue-jun, ZHAO Wen-bin. RESEARCH ON PROPERTIES OF A ABLATIVE MODIFIED PHENOLIC RESIN[J]. COMPOSITES SCIENCE AND ENGINEERING, 2015, 0(7): 18-21.

参考文献

[1] Scott W B, Crmg R H. Resin transfer molding:A decade of technology advance[J]. Sampe Journal, 1998, (6): 3-23.
[2] 齐燕燕, 刘亚青, 张彦飞. 新型树脂传递模塑技术[J]. 化工新材料, 2006, 34(2): 36-38.
[3] 黄发荣, 万里强, 等. 酚醛树脂及其应用[M]. 北京: 化学工业出版社, 2011.
[4] Salla JM, Cadenato A, Ramis X, et al. Thermoset Cure Kinetcs by Isoconversional Methods[J]. Journal of Thermal Analysis and Calorimetry, 1999, 56: 771-781.
[5] 赵卫生, 孙超明, 王文晶, 等. RTM用乙烯基酯树脂化学流变性研究[J]. 玻璃钢/复合材料, 2014, (8): 97-100.
[6] 石凤, 段跃新, 梁志勇, 等. RTM专用双马来酰亚胺树脂体系化学流变性[J]. 复合材料学报, 2006, 23(1): 56-62.
[7] Kerdall K. Characterization of RTM process[J]. Composite Manufacturing, 1992, 3(4): 235-277.
[8] 黄家康, 岳红军, 董永祺. 复合材料成型技术[M]. 北京: 化学工业出版社, 1999.
[9] 王柏臣. RTM 成型石英纤维/酚醛树脂细观浸润过程研究[D]. 哈尔滨:哈尔滨工业大学, 2005.
[10] Karkanas P I, ParmaSe I K. Modeling the cure of a corninertial epoxy resin for application in resin tranfer molding[J]. Polymcr International, 1996, 41(2): 183-192.
[11] 马青松, 陈朝辉, 郑文伟, 等. 树脂传递模塑-复合材料成型新工艺[J]. 材料科学与工程, 2000, (18): 92-97.
[12] KimHJ, BrunovskaZ, IshidaH. Synthesisand thermal characterization of polybenzoxazines based on acetylenefunctional monomers[J]. Po-lymer, 1999, 40: 6565-6570.
[13] A C Loos, G S Springer. Curing of epoxy matrix composites[J]. Journal of compositematerials, 1983, 17(3): 135-167.
[14] 梁志勇, 段跃新, 林云, 等. RTM专用混合型树脂体系研究-反应特性与工艺特性研究[J]. 玻璃钢/复合材料, 2000, (5): 14-17.
[15] 李建伟. 石英/酚醛复合材料RTM 成型工艺及性能研究[D]. 长沙: 国防科学技术大学, 2008.
[16] 纪凤龙, 顾宜, 谢美丽, 等. 苯并恶嗪树脂烧蚀性能的初步研究[J]. 宇航材料工艺, 2002, (1): 25-29.