CNG-2型气瓶缠绕层树脂开裂影响因素研究

玻璃钢/复合材料 ›› 2016, Vol. 0 ›› Issue (10): 26-31.

CNG-2型气瓶缠绕层树脂开裂影响因素研究

刘林林,向忠^*,胡旭东,陆海亮

浙江理工大学机械与自动控制学院,杭州310018

收稿日期:2016-05-25 出版日期:2016-11-25 发布日期:2016-11-25
通讯作者: 向忠(1982-),男,博士,副教授,主要从事复合材料结构方面的研究。
作者简介:刘林林(1989-),男,硕士研究生,主要从事CNG-2气瓶缠绕层方面的研究。
基金资助:
国家科技支撑计划项目(2014BAF06B03)

STUDY ON WOUND LAYER RESIN CRACKING FACTORS FOR CNG-2 TYPE CYLINDERS

LIU Lin-Lin, XIANG Zhong^*, HU Xu-Dong, LU Hai-Liang

Faculty of Mechanical Engineering & Automation, Zhejiang Sci-Tech University, Hangzhou 310018, China

Received:2016-05-25 Online:2016-11-25 Published:2016-11-25

摘要/Abstract

摘要： 针对CNG气瓶在自紧工艺中缠绕层会产生一定的树脂开裂这一问题,讨论复合材料本身属性对缠绕层树脂开裂的影响。提出一种多尺度建模方法,利用微观力学的方法探讨缠绕层的含胶量和纤维直径对树脂开裂程度的影响。结果表明树脂开裂程度随着含胶量的增大而减少,在企业生产的含胶量范围内,含胶量为34%时树脂开裂程度最小。在含胶量为34%时,利用多尺度模型研究了纤维直径对树脂开裂程度的影响,结果表明纤维直径对树脂开裂程度几乎没有影响。由于含胶量是由缠绕张力控制的,因此合理控制缠绕张力可以减少树脂开裂程度。实验验证了模型的准确性并为研究提供了参考,该研究可为改进CNG-2气瓶生产提供理论依据。

关键词: CNG, 气瓶, 含胶量, 缠绕层, 开裂

Abstract: Aiming at improving compressed nature gas (CNG) cylinders wound layer resin anti-crack characteristic, a multi-scale modeling method is proposed to investigate the resin cracking mechanism. In the simulation model, the influences of gel content of winding layer and fiber diameter was discussed by micro-mechanics approach. Simulation results indicate that resin cracking degree is reduced as the gel content increases, and the resin cracking degree reaches the minimum point while the gel content was set to 34%. Then the influence of fiber diameter on the resin crack was discussed using a multi-scale model by setting gel content to 34%, and the simulation results indicate that fiber diameter almost has no effect on the cracking of the resin. Finally, the validaty of the multi-scale model is verified by experimental results. Since the gel content can be adjusted by precisely control the winding tensions, the study can be adopted to reduce the degree of resin cracking and provide the theoretical reference for improving the production of CNG-2 cylinders.

Key words: CNG, cylinder, gel content, winding layer, cracking

中图分类号:

TB332

刘林林,向忠,胡旭东,陆海亮. CNG-2型气瓶缠绕层树脂开裂影响因素研究[J]. 玻璃钢/复合材料, 2016, 0(10): 26-31.

LIU Lin-Lin, XIANG Zhong, HU Xu-Dong, LU Hai-Liang. STUDY ON WOUND LAYER RESIN CRACKING FACTORS FOR CNG-2 TYPE CYLINDERS[J]. Fiber Reinforced Plastics/Composites, 2016, 0(10): 26-31.

参考文献

[1] Liu J, Zhang X, Wang T, et al. Experimental and numerical study of the pollution formation in a diesel/CNG dual fuel engine[J]. Fuel, 2015, 159: 418-429.
[2] Takeshita T. Assessing the co-benefits of CO₂ mitigation on air pollutants emissions from road vehicles[J]. Applied Energy, 2012, 97: 225-237.
[3] Khan MI, Yasmin T, Shakoor A. Technical overview of compressed natural gas (CNG) as a transportation fuel[J]. Renewable and Sustainable Energy Reviews, 2015, 51: 785-797.
[4] 李斌, 於秋霞, 熊姝涛, 等. CNG-2型气瓶用玻璃纤维增强材料耐腐蚀性能分析[J]. 压力容器, 2015, 32(1): 1-8.
[5] 元世海, 李彦虎, 祖磊, 等. 纤维缠绕车载CNG气瓶的结构设计及其有限元分析[J]. 玻璃钢/复合材料,2015(12): 12-17.
[6] Shahani AR, Kheirkhah MM. Stress intensity factor calculation of steel-lined hoop-wrapped cylinders with internal semi-elliptical circumferential crack[J]. Engineering Fracture Mechanics, 2007, 74(13): 2004-2013.
[7] 郭崇志, 甘平燕, 付小立. 复合材料缠绕层缺陷深度对CNG-2气瓶强度影响的研究[J]. 压力容器, 2013, 30(3): 5-14.
[8] 谢志刚, 陈小芹. 车用CNG2气瓶金属内胆低周疲劳行为分析[J]. 工业安全与环保, 2014, 40(5): 48-50.
[9] 李斌, 马凯, 由宏新. 缠绕层表面缺陷对CNG-2复合气瓶爆破压力的影响[J]. 压力容器, 2014, 31(4): 1-6.
[10] Li GF, Yuan YF, Lu X. Microstructure and stress corrosion cracking of Dissimilar Metal Weld 16MND5/309L/308L/Z2CND18-12N Used for Connecting Reactor Pressure Vessel to Piping in Nuclear Power Plants[J]. Procedia Engineering, 2015, 130: 1572-1579.
[11] Song FM. Predicting the mechanisms and crack growth rates of pipelines undergoing stress corrosion cracking at high pH[J].Corrosion Science, 2009, 51(11): 2657-2674.
[12] Meresht SE, Farahani ST, Neshati J. Failure analysis of stress corrosion cracking occurred in a gas transmission steel pipeline[J]. Engineering Failure Analysis, 2011,18(3): 963-970.
[13] 成志刚. 自紧压力对车用玻璃纤维环向缠绕气瓶疲劳次数的影响研究[J]. 玻璃钢/复合材料, 2014(10): 70-74.
[14] González C, LLorca J. Multiscale modeling of fracture in fiber-rein-forced composites[J]. Acta Materialia, 2006, 54(16): 4171-4181.
[15] Romanowicz M. A numerical approach for predicting the failure locus of fiber reinforced composites under combined transverse compression and axial tension[J]. Computational Materials Science, 2012, 51(1): 7-12.
[16] Melro AR, Camanho PP, Andrade Pires FM, et al. Micromechanical analysis of polymer composites reinforced by unidirectional fibers: Part II-Micromechanical analyses[J]. International Journal of Solids and Structures, 2013, 50(11): 1906-1915.