纤维-金属混合夹层梁弯曲性能试验研究

玻璃钢/复合材料 ›› 2016, Vol. 0 ›› Issue (5): 12-16.

纤维-金属混合夹层梁弯曲性能试验研究

丁洁明,刘伟庆^*,万里,王璐

南京工业大学土木工程学院,南京211816

收稿日期:2015-12-04 出版日期:2016-05-25 发布日期:2016-05-25
通讯作者: 刘伟庆(1964-),男,博士,博士生导师,主要从事复合材料研究,wqliu@njut.edu.cn。
作者简介:丁洁明(1989-),男,硕士研究生,主要从事复合材料结构研究。
基金资助:
国家自然科学基金(51208251);江苏省高校自然科学基金重大项目(15KJA560001);国家自然科学基金重点项目(51238003)

EXPERIMENTAL STUDY ON FLEXURAL PERFORMANCE OFFIBER-METAL HYBRID SANDWICH BEAM

DING Jie-ming, LIU Wei-qing^*, WAN Li, WANG Lu

College of Civil Engineering, Nanjing Tech University, Nanjing 211816, China

Received:2015-12-04 Online:2016-05-25 Published:2016-05-25

摘要/Abstract

摘要： 对纤维-金属混合夹层梁(FMS)进行试验,该结构自上而下主要由无碱玻璃纤维、带齿钉金属板、泡桐木、带齿钉金属板、无碱玻璃纤维组成,其中金属板与泡桐木之间采用齿钉相连,金属板与无碱玻璃纤维之间采用不饱和聚酯树脂粘结。通过四点弯曲试验,得到了纤维-金属混合夹层梁(FMS)在不同跨高比下的弯曲性能和破坏模式,并与纤维增强夹层梁(FSS)进行对比,同时根据不同的破坏模式采用不同的理论公式对FMS试件承载力进行验证,结果表明,在跨高比为10、12、16、20、24时,FMS的极限承载力及抗弯刚度均得到了提高,理论求得的承载力值与试验值吻合较好。

关键词: 纤维-金属混合夹层梁, 弯曲性能, 破坏模式, 抗弯刚度

Abstract: In this paper, the fiber-metal hybrid sandwich beam (FMS) was fabricated. From top to bottom, alkali-free glass fiber, the metal sheet with tooth nail, paulownia wood, the metal sheet with tooth nail and alkali-free glass fiber were arranged. Tooth nail was used to connect the metal plate with paulownia and unsaturated polyester resin was used to connect the metal plate with non-alkali fiber glass. According to four-point bending tests, the bending performance and failure modes of FMS with different span-depth ratio were investigated and compared with the ordinary fiber reinforced sandwich beam (FSS). An analytical formula to identify failure modes was also obtained to validate the bearing capacity. The test results show that when span-depth of the beam were 10, 12, 16, 20, 24, the ultimate bearing capacity and bending stiffness of the FMS were increased. The calculated bearing capacity agreed well with the experiment results.

Key words: fiber-metal hybrid sandwich beam, bending property, failure mode, bending stiffness

中图分类号:

TB332

丁洁明,刘伟庆,万里,王璐. 纤维-金属混合夹层梁弯曲性能试验研究[J]. 玻璃钢/复合材料, 2016, 0(5): 12-16.

DING Jie-ming, LIU Wei-qing, WAN Li, WANG Lu. EXPERIMENTAL STUDY ON FLEXURAL PERFORMANCE OFFIBER-METAL HYBRID SANDWICH BEAM[J]. Fiber Reinforced Plastics/Composites, 2016, 0(5): 12-16.

参考文献

[1] Zhang JX, Qin QH, Wang TJ. Compressive strength and dynamic response of corrugated metal sandwich plates with unfilled and foam-filled sinusoidal plate cores[J]. Acta Mechanica, 2013, 224(4): 759-775.
[2] Wang ZJ, Qin QH, Zhang JX, et al. Low velocity impact response of geometrically asymmetric slender sandwich beams with metal foam core[J]. Composite Structures, 2013, 98: 1-14.
[3] Lu TJ, Liu T, Deng ZC. Thermoelastic properties of sandwich materials with pin-reinforced foam cores[J]. Science in China Series E: Technological Sciences, 2008, 51(22): 2059-2074.
[4] Pan SD, Wu LZ, Sun YG, et al. Fracture test for double cantilever beam of honeycomb sandwich panels[J]. Mater Lett, 2008, 62: 523-526.
[5] Hou SJ, Ren LL, Dong D, et al. Crashworthiness optimization design of honeycomb sandwich panel based on factor screening[J]. Journal of Sandwich Structures and Materials, 2012, 14(6): 665-678.
[6] A.P.Mouritz, E.Gellert. Review of advanced composite structures for naval ships and submarines[J]. Composite Structures, 2001, 53(1): 2-41.
[7] Dai J. Fatigue assessment methodology for sandwich panels[D]. Los Angeles: University of California los Angeles, 2002.
[8] James. W G. Influence of reinforcement type on the mechanical behavior and fire response of hybrid composites and sandwich structures[D]. New Brunswick: The state university of New jersey, 2004.
[9] Mamalis, A.G., Spentzas, K.N., et al. A new hybrid concept for sa-ndwich structures[J]. Composite Structures, 2008, 83(4): 335-340.
[10] 谢佳卉,周建锋,杨胜春. GLARE层压板的力学性能研究[J]. 结构强度研究, 2009(1): 14.
[11] 方海, 刘伟庆, 万里. 点阵增强型复合材料夹层结构的力学性能实验与分析[J]. 实验力学, 2010(5): 522-528.
[12] 万里, 刘伟庆, 周叮, 等. 齿槽增强泡桐木夹层结构界面性能试验[J]. 南京工业大学大学学报, 2010(5): 1-5.
[13] American Society of Testing and Materials Standard C393-62 Test Method for Flexural Properties of Sandwich Constructions[Z]. Annual Book of ASTM Standards, 2000.
[14] Mohan K, Hon YT, Idapalapati S, et al. Failure of sandwich beams consisting of alumina face sheet and aluminum foam core in bending[J]. Materials Science and Engineering. A, 2005, 409(1): 292-301.
[15] Allen, H.G.. Analysis and Design of Structural Sandwich Panels[Z]. Pergamon, New York.