基于ABAQUS软件的U形薄壳加肋结构热变形分析

玻璃钢/复合材料 ›› 2017, Vol. 0 ›› Issue (12): 41-44.

基于ABAQUS软件的U形薄壳加肋结构热变形分析

丁常方,张晶^*,褚洪杰,尹亮

航天材料及工艺研究所,北京100076

收稿日期:2017-06-26 出版日期:2017-12-20 发布日期:2017-12-20
通讯作者: 张晶(1985-),女,工程师,博士,主要从事树脂基结构复合材料方面的研究,zj01141985@tju.edu.cn。
作者简介:丁常方(1983-),男,主要从事航天结构材料成型工艺方面的研究

THERMAL DEFORMATION ANALYSIS OF THE U-SHAPED THIN SHELL STRUCTURES WITH STIFFENERS BASED ON ABAQUS

DING Chang-fang, ZHANG Jing^*, CHU Hong-jie, YIN Liang

Aerospace Research Institute of Materials & Processing Technology, Beijing 100076, China

Received:2017-06-26 Online:2017-12-20 Published:2017-12-20

摘要/Abstract

摘要： U形薄壳加肋结构在航空航天领域应用广泛,然而由于产品截面热变形,需要用专用工装或分别测量进行定位制孔,工序烦琐,制造周期较长。以经典层合板理论为依据,借助ABAQUS软件建立U形薄壳加肋结构的有限元模型,对其截面尺寸进行计算和预测,并与实际产品对比,结果表明:在局部建模中考虑钢模具的计算条件下的预测数值与实际产品基本一致,而由于整体建模未考虑树脂在固化变形中的作用,其计算结果较实际截面尺寸偏小;ABAQUS软件可用于该结构铺层产品的热变形预测。

关键词: ABAQUS软件, 薄壳加肋结构, 热变形

Abstract: The U-shaped thin shell structures with stiffeners are widely used in the field of aeronautic and aerospace. However, due to the thermal deformation of the cross section of the structures, the hole-position and drilling are carried out by the special production tools or separate measurement, which lead to the complex procedure and long manufacture cycle. In this study, the finite element analysis of ABAQUS was employed to calculate and predict the sectional dimension of the U-shaped thin shell structure. The results show that the predictive values in the design condition of local modeling with steel tool were consistence with that of the actual products. While the calculating results of the integrated modeling were smaller than that of actual dimension, which could be attributed to the consideration without steel tools in this modeling. It is concluded that the ABAQUS can be used for the thermal analysis and prediction of the U-shaped thin shell structure with stiffeners.

Key words: ABAQUS software, thin shell structure with stiffeners, thermal deformation

中图分类号:

TB332

丁常方,张晶,褚洪杰,尹亮. 基于ABAQUS软件的U形薄壳加肋结构热变形分析[J]. 玻璃钢/复合材料, 2017, 0(12): 41-44.

DING Chang-fang, ZHANG Jing, CHU Hong-jie, YIN Liang. THERMAL DEFORMATION ANALYSIS OF THE U-SHAPED THIN SHELL STRUCTURES WITH STIFFENERS BASED ON ABAQUS[J]. Fiber Reinforced Plastics/Composites, 2017, 0(12): 41-44.

参考文献

[1] 刘芳芳, 李晓丹, 高赫, 等. 先进复合材料帽形加强肋的设计与应用[J]. 纤维复合材料, 2007(2): 25-26.
[2] 刘文一, 焦冀光. 某飞行器复合材料薄壁加筋结构舱段稳定性分析[J]. 舰船电子工程, 2013, 36(2): 110-113.
[3] 劳俊, 殷炳帅. 大尺度吸收塔环向加劲肋布置对结构稳定性影响研究[J]. 特种结构, 2016, 33(4): 79-84.
[4] 梁吉鹏, 马斌捷. 复合材料层合结构层间应力分析综述[J]. 强度与环境, 2013, 40(2): 33-42.
[5] 徐子航, 刘东, 钱群, 等. 连续纤维增强热塑性复合材料热变形性能研究进展[J]. 玻璃钢/复合材料, 2015(10): 83-86, 63.
[6] 黄立新, 杨真真, 张晓磊, 等. 基于ABAQUS的功能梯度材料等梯度有限元分析[J]. 玻璃钢/复合材料, 2014(2): 33-39.
[7] 梁俊. 内加筋风力机塔筒风致动力响应与稳定性能研究[D]. 南京: 南京航空航天大学, 2015.
[8] 张丽、李楠, 张媛媛, 等. 高性能环氧树脂基体的研究进展[J]. 材料导报, 2013, 27(S2): 242-244.
[9] 赵振, 刘才山, 陈滨, 等. 薄壁加筋肋圆柱壳稳定性分析的参数化研究[J]. 力学与实践, 2004, 26(2): 17-21.
[10] 郭战胜, 杜善义, 张博明, 等. 先进复合材料用环氧树脂的固化反应和化学流变[J]. 复合材料学报, 2004, 21(4): 146-151.
[11] 崔静, 郑伟峰, 谭昌柏, 等. 复合材料传动轴固化成形的变形预测与补偿[J]. 机械制造, 2015, 44(6): 21-24.
[12] Zhu Qi, Geubelle Philippe H, Li Min, et al. Dimensional accuracy of thermoset composites: simulation of process-induced residual stress[J]. Journal of composites materials, 2001, 35(24): 2171-2205.
[13] 陈祥宝, 邢丽英, 周正刚. 树脂基复合材料制造过程温度变化模拟研究[J]. 航空材料学报, 2009(2): 61-65.
[14] 张继奎, 郦正能, 关志东, 等. 热固性复合材料固化过程三维有限元模拟和预测[J]. 复合材料学报, 2009, 26(1): 174-178.
[15] 邓火英, 张佐光, 顾轶卓, 等. L形层板真空袋成型缺陷的实验研究[J]. 复合材料学报, 2007, 24(4): 34-39.
[16] Li Min, Tucker Ⅲ C L. Modeling and simulation of two-dimensional consolidation for thermoset matrix composites[J]. Composites Part A, 2002, 33(6): 877-892.