复合材料螺栓连接渐近失效分析

玻璃钢/复合材料 ›› 2017, Vol. 0 ›› Issue (7): 40-44.

复合材料螺栓连接渐近失效分析

梅俊杰, 倪爱清^*, 王继辉

武汉理工大学材料复合新技术国家重点实验室,武汉430070

收稿日期:2016-12-06 出版日期:2017-07-28 发布日期:2017-07-28
通讯作者: 倪爱清(1975-),女,博士,副研究员,主要从事复合材料力学方面的研究,aqni21stcn@163.com 。
作者简介:梅俊杰(1993-),男,硕士,主要从事复合材料结构设计方面的研究。

PROGRESSIVE DAMAGE ANALYSIS OF COMPOSITE BOLTED JOINTS

MEI Jun-jie, NI Ai-qing^*, WANG Ji-hui

State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070, China

Received:2016-12-06 Online:2017-07-28 Published:2017-07-28

摘要/Abstract

摘要： 为了研究预紧力和摩擦系数对复合材料螺栓连接强度的混合影响及其机理,使用ANSYS软件建立了复合材料层合板单钉连接的三维有限元模型。采用渗透接触法来模拟螺栓的预紧力,考虑各组件之间的接触摩擦和结构二次弯曲的影响,使用改进后的三维Hashin失效准则和Camanho退化模型,对复合材料单钉连接进行渐进失效分析。数值模拟结果与文献中的实验结果吻合良好。分析结果表明,增大接触面的摩擦系数和施加合适的预紧力均能提高接头强度。摩擦系数小时,通过增加预紧力来提高接头强度的效果不明显,反而使复合材料容易发生基体开裂。在施加预紧力的同时应综合考虑摩擦系数的大小。

关键词: 复合材料, 螺栓连接, 渐进失效, 摩擦系数, 预紧力

Abstract: In order to investigate the combined influence of friction coefficient and bolt-torque on the strength of single-bolted composite joints and their mechanism, a three-dimensional finite element model of laminate in single-bolted joints has been built in ANSYS software. The bolted-torque is applied by using penetrative contact method. The influence of friction in components and secondary bending of the plates has been considered. The progressive damage analysis of composite bolted joints is implemented by using improved Hashin failure criterion and Camanho degradation model. The model is validated through comparison with experimental data in literature. It is shown that the joint strength can be enhanced by increasing the friction coefficient and applying appropriate bolt-torque. Increment in the bolt-torque cannot improve the joint strength obviously and higher bolt-torque can make the matrix crushing when the friction coefficient is small. Thus friction coefficient should be considered when applying bolt-torque. The results are instructive for engineering application.

Key words: composites, bolt joint, progressive damage, friction coefficient, torque

中图分类号:

TB332

梅俊杰, 倪爱清, 王继辉. 复合材料螺栓连接渐近失效分析[J]. 玻璃钢/复合材料, 2017, 0(7): 40-44.

MEI Jun-jie, NI Ai-qing, WANG Ji-hui. PROGRESSIVE DAMAGE ANALYSIS OF COMPOSITE BOLTED JOINTS[J]. Fiber Reinforced Plastics/Composites, 2017, 0(7): 40-44.

参考文献

[1] McCarthy M. BOJCAS: bolted joints in composite aircraft structures[J]. Air & Space Europe, 2001, 3(3-4): 139-142.
[2] Hühne C, Zerbst A K, Kuhlmann G, et al. Progressive damage analysis of composite bolted joints with liquid shim layers using constant and continuous degradation models[J]. Composite Structures, 2010, 92(2): 189-200.
[3] McCarthy M A, McCarthy C T, Lawlor V P, et al. Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: part I-model development and validation[J]. Composite Structures, 2005, 71(2): 140-158.
[4] Dano M-L, Kamal E, Gendron G. Analysis of bolted joints in composite laminates: Strains and bearing stiffness predictions[J]. Composite Structures, 2007, 79(4): 562-570.
[5] McCarthy C T. Experiences with Modeling Friction in Composite Bolted Joints[J]. Journal of Composite Materials, 2005, 39(21): 1881-1908.
[6] Olmedo , Santiuste C. On the prediction of bolted single-lap composite joints[J]. Composite Structures, 2012, 94(6): 2110-2117.
[7] 王佳宁,赵美英. 预紧力对层合板螺栓连接强度的影响研究[J]. 航空工程进展, 2012, 3(2): 189-194.
[8] 陈昆昆,刘龙权. 过盈配合和预紧力的混合作用对复合材料机械连接结构的影响及其机制[J]. 复合材料学报, 2013, 30(6): 243-251.
[9] Riccio A. Effects of Geometrical and Material Features on Damage Onset and Propagation in Single-lap Bolted Composite Joints under Tensile Load: Part I-Experimental Studies[J]. Journal of Composite Materials, 2005, 39(23): 2071-2090.
[10] 李会勋,胡迎春. 利用ANSYS模拟螺栓预紧力的研究[J]. 山东科技大学学报(自然科学版), 2006, 25(1): 57-59.
[11] Barbero E J. Finite Element Analysis of Composite Materials Using ANSYS^, Second Edition[M]. CRC Press, 2013.
[12] Herrington P D, Sabbaghian M. Factors affecting the friction coefficients between metallic washers and composite surfaces[J]. Composites, 1991, 22(6): 418-424.
[13] McCarthy C T, McCarthy M A, Lawlor V P. Progressive damage analysis of multi-bolt composite joints with variable bolt-hole clearances[J]. Composites Part B: Engineering, 2005, 36(4): 290-305.
[14] 黄争鸣. 纤维增强复合材料强度理论的研究现状与发展趋势——“破坏分析奥运会”评估综述[J]. 力学进展, 2007, 37(1): 80-98.
[15] P.P.Camanho. A Progress Damage Model for Mechanically Fastened Joints in Composite Laminates[J]. Journal of Composite Materials, 1999, 33(24): 2248-2280.
[16] Tserpes K I, Labeas G, Papanikos P, et al. Strength prediction of bolted joints in graphite/epoxy composite laminates[J]. Composites Part B: Engineering, 2002, 33(7): 521-529.