含缺陷复合材料加筋壁板承载能力的数值预测

玻璃钢/复合材料 ›› 2018, Vol. 0 ›› Issue (2): 28-35.

含缺陷复合材料加筋壁板承载能力的数值预测

周正根¹, 曹东风², 胡海晓¹, 钟愉承¹

1.武汉理工大学理学院,武汉430070;
2.武汉理工大学材料复合新技术国家重点实验室,武汉430070

收稿日期:2017-07-17 出版日期:2018-02-28 发布日期:2018-02-28
通讯作者: 李书欣(1958-),男,博士,教授,主要从事先进航空材料和工程方面的研究,sxlwutbu01@163.com。
作者简介:周正根(1991-),男,硕士研究生,主要从事复合材料力学与结构设计方面的研究。
基金资助:
中央高校基本科研业务费资助(175214002)

NUMERICAL SIMULATION OF CARRYING CAPACITY OF COMPOSITE REINFORCED PANELS WITH DEFECT

ZHOU Zheng-gen¹, CAO Dong-feng², HU Hai-xiao¹, ZHONG Yu-cheng¹

1.School of Science, Wuhan University of Technology, Wuhan 430070, China;
2.State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan 430070, China

Received:2017-07-17 Online:2018-02-28 Published:2018-02-28

摘要/Abstract

摘要： 碳纤维复合材料加筋壁板是飞机结构的典型部件,成型过程中的制造缺陷对其极限承载能力和失效行为具有显著影响,是结构完整性评估的重要内容。通过数值手段开展了3点弯曲载荷作用下含缺陷复合材料加筋壁板的数值分析,重点考虑了缺陷尺寸和位置对结构承载能力的影响。首先基于Abaqus/Standard建立了加筋壁板的三维有限元模型,引入双线性内聚力模型用于描述复合材料加筋壁板的层间失效行为,然后结合文献相关实验数据验证了该模型的有效性,最后基于该有限元模型研究了缺陷尺寸和位置对结构承载能力的影响。结果表明:建立的有限元模型计算结果与文献实验结果吻合;结构的承载能力随着缺陷尺寸的增大而降低,且对蒙皮/桁条界面中部缺陷较为敏感;缺陷的存在导致结构的破坏模式发生转变,但起始裂纹始终发生在界面附近的基体区域。

关键词: 复合材料, 加筋壁板, 缺陷, 内聚力模型, 承载能力

Abstract: Carbon fiber composite Skin/Stringer is a typical component of aircraft structure. However, the manufacturing process of laminated composite structure can lead to the existence of defects in the bonds. The pre-existing defects have a great effect on the ultimate bearing capacity and failure behavior of Skin/Stringer. Therefore, it is important to assess structural integrity. In this paper, the specimens were subjected to three-point bending. To evaluate the debonding mechanisms between the skin and the stringer, different sizes and locations of defects were taken into consideration. First, a three-dimensional finite element model based on Abaqus/Standard was established, and the bilinear cohesive zone model (CZM) was used to simulate the interface failure between the skin and the stringer; Then, the validity of the model were verified through the experimental data of the literatures. Finally based on the finite element model, the influence of the sizes and locations of the defects on the failure modes and the load-carrying capacity of the structure were investigated. The result indicats that the calculated results show good agreement with those of experiments. The load capacity of the structure is found to decrease with increasing defect size, and Skin-Stringer is very sensitive to defects at the middle of the interface; The failure modes of the Skin/Stringer changes because of the pre-existing defects. But the initial crack always occurs in the matrix near the interface area.

Key words: composite, stiffener, defects, cohesive zone model, carrying capacity

中图分类号:

TB332

周正根, 曹东风, 胡海晓, 钟愉承. 含缺陷复合材料加筋壁板承载能力的数值预测[J]. 玻璃钢/复合材料, 2018, 0(2): 28-35.

ZHOU Zheng-gen, CAO Dong-feng, HU Hai-xiao, ZHONG Yu-cheng. NUMERICAL SIMULATION OF CARRYING CAPACITY OF COMPOSITE REINFORCED PANELS WITH DEFECT[J]. Fiber Reinforced Plastics/Composites, 2018, 0(2): 28-35.

参考文献

[1] 杜凯, 矫桂琼, 王翔. 含不同长度切口的复合材料加筋板的轴向压缩研究[C]//第十五届全国复合材料学术会议. 哈尔滨: 2008.
[2] Ronald Krueger, Micahel K. Cvitkovich, T. Kevin O′brien, et al. Testing and analysis of composite skin/stringer debonding under multi-axial loading[J]. Journal of Composite Materials, 2000, 34(15): 754-755.
[3] Raimondo A, Riccio A. Inter-laminar and intra-laminar damage evolution in composite panels with skin-stringer debonding under compression[J]. Composites Part B Engineering, 2016, 94: 139-151.
[4] Riccio A, Russo A, Raimondo A, et al. A numerical assessment of fibre bridging influence on composite panels skin-stringer debonding[J]. Procedia Engineering, 2016, 167: 56-63.
[5] Camanho P P, DVila C G, Pinho S T. Fracture analysis of composite co-cured structural joints using decohesion elements[J]. Fatigue & Fracture of Engineering Materials & Structures, 2010, 27(9): 745-757.
[6] Bertolini J, Castanié B, Barrau J J, et al. Multi-level experimental and numerical analysis of composite stiffener debonding. Part 1: Non-specific specimen level[J]. Composite Structures, 2009, 90(4): 381-391.
[7] 朱亮, 崔浩, 李玉龙, 等. 含缺陷复合材料T型接头失效数值分析[J]. 航空学报, 2012, 33(2): 287-296.
[8] 崔浩, 李玉龙, 刘元镛, 等. 基于粘聚区模型的含填充区复合材料接头失效数值模拟[J]. 复合材料学报, 2010, 27(2): 161-168.
[9] Wagner W, Balzani C. Simulation of delamination in stringer stiffened fiber-reinforced composite shells[J]. Computers & Structures, 2008, 86(9): 930-939.
[10] Zhou D W, Louca L A, Saunders M. Numerical simulation of sandwich T-joints under dynamic loading[J]. Composites Part B Engineering, 2008, 39(6): 973-985.
[11] Turon A, Dvila C G, Camanho P P, et al. An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models[J]. Engineering Fracture Mechanics, 2007, 74(10): 1665-1682.
[12] 赵丽滨, 徐吉峰. 先进复合材料连接结构分析方法[M]. 北京: 北京航空航天大学出版社, 2015.
[13] Jiang W G, Hallett S R, Green B G, et al. A concise interface constitutive law for analysis of delamination and splitting in composite materials and its application to scaled notched tensile specimens[J]. International Journal for Numerical Methods in Engineering, 2010, 69(9): 1982-1995.
[14] Alfano G, Crisfield M A. Finite element interface models for the delamination analysis of laminated composites: mechanical and computational issues[J]. International Journal for Numerical Methods in Engineering, 2001,50(7): 1701-1736.
[15] Needleman A. A continuum model for void nucleation by inclusion debonding[J]. Journal of Applied Mechanics, 1987, 54(3): 525.
[16] Tvergaard V, Hutchinson J W. The influence of plasticity on mixed mode interface toughness[J]. Journal of the Mechanics & Physics of Solids, 1993, 41(6): 1119-1135.
[17] Mi Y, Crisfield M, Davies G, et al. Progressive delamination using interface elements[J]. Journal of composite materials, 1998,14(32): 1246-1272.
[18] Chang F K, Springer G S. The strengths of fiber reinforced composite bends[J]. Journal of Composite Materials, 1986, 20(1): 30-45.
[19] Benzeggagh M L, Kenane M. Measurement of mixed-mode delamination fracture toughness of unidirectional glass/epoxy composites with mixed-mode bending apparatus[J]. Composites Science & Technology, 1996, 56(4): 439-449.
[20] Camanho P P, Davila C G, De Moura M F. Numerical simulation of mixed-mode progressive delamination in composite materials[J]. Journal of Composite Materials, 2003, 37(16): 1415-1438.
[21] 李吻, 李勇, 还大军, 等. Z-pin增强复合材料帽型单加筋板弯曲性能[J]. 航空学报, 2016, 37(12): 3843-3852.