玻璃纤维-铝合金层合板补强拉伸性能及破坏机理研究

玻璃钢/复合材料 ›› 2018, Vol. 0 ›› Issue (2): 36-40.

玻璃纤维-铝合金层合板补强拉伸性能及破坏机理研究

崔海超¹, 王海鹏²

1.中航工业复合材料技术中心,北京101300;
2.北京航空材料研究院,北京100095

收稿日期:2017-09-18 出版日期:2018-02-28 发布日期:2018-02-28
作者简介:崔海超(1984-),男,硕士,主要从事树脂基复合材料超混杂方面的研究,chcniat@163.com。

RESEARCH OF REPAIRING PERFORMANCE AND FAILURE MECHANISM OF GLASS FIBER-ALUMINUM LAMINATES

CUI Hai-chao¹, WANG Hai-peng²

1.AVIC Composite Technology Center,Beijing 101300, China;
2.Beijing Institute of Aeronautical Materials, Beijing 100095, China

Received:2017-09-18 Online:2018-02-28 Published:2018-02-28

摘要/Abstract

摘要： 对含预置孔缺陷的玻璃纤维-铝合金层合板修补前后进行了拉伸试验,讨论了拉伸过程中载荷随拉伸位移的变化趋势,并分析了补强片对于材料拉伸强度的影响及断裂破坏形式。结果表明,修补前后的玻璃纤维-铝合金层合板在拉伸过程中均经历了屈服阶段,修补后的层合板表现出了更明显的屈服现象,且载荷在破坏前出现了较大波动,孔直径为6 mm、10 mm、12 mm的缺陷试样在补强后的极限强度修复率分别为17.7%、13.2%、20.6%,补强片使层合板在拉伸破坏后在断裂位置呈现双扇形损伤,补强片的破坏为胶膜的剪切破坏,破坏界面位于铝合金表面。

关键词: 玻璃纤维-铝合金层合板, 修补, 补强片

Abstract: The tensile test was carried out before and after the repairing of the glass fiber-aluminum laminates with presetting hole defects. The influence of the load on the tensile displacement during the stretching process was discussed, and the influence of the reinforcing sheet on the tensile strength of the material was analyzed. The results show that all the glass fiber-aluminum laminates have experienced the yield stage, the repaired laminates exhibit a more obvious yield phenomenon, and the load fluctuates greatly before the damage. The ultimate strength of the repair rate was 17.7%, 13.2%, 20.6%, respectively, for the aminates, containing 6 mm,10 mm,12 mm hole defects. Due to the repairing plates, the laminates showed double fan damage in the fracture position after the tensile fracture. The damage form of the repairing plates was shear failure of the film, which occurred on the surface of the aluminum alloy.

Key words: glass fiber-aluminum laminates, repairing, repairing plate

中图分类号:

TB332

崔海超, 王海鹏. 玻璃纤维-铝合金层合板补强拉伸性能及破坏机理研究[J]. 玻璃钢/复合材料, 2018, 0(2): 36-40.

CUI Hai-chao, WANG Hai-peng. RESEARCH OF REPAIRING PERFORMANCE AND FAILURE MECHANISM OF GLASS FIBER-ALUMINUM LAMINATES[J]. Fiber Reinforced Plastics/Composites, 2018, 0(2): 36-40.

参考文献

[1] 曹增强. 纤维金属层板及其在飞机结构中的应用[J]. 航空制造技术, 2006(6): 60-62.
[2] 万云, 童谷生. 金属与复材混杂层板受高速冲击时的吸能分析[J]. 兵器材料科学与工程,2016, 39(1): 22-26.
[3] 王世明. 大飞机用GLARE层板的性能综合评价研究[J]. 材料导报, 2010, 24(9): 88-94.
[4] 陶杰, 李华冠, 潘蕾, 等. 纤维金属层板的研究与发展趋势[J]. 南京航空航天大学学报,2015, 47(05): 626-636.
[5] 介苏朋. 纤维金属层板(FMLs)结构制造方法研究[D]. 西安: 西北工业大学, 2006.
[6] AD VLOT. Fiber metal laminates an introduction[J]. The Netherlands: Kluwer Academic, 2001: 260-272.
[7] C. A. J. R. Vermeeren.Glare design aspects and philosophies[J]. Composite Materials, 2003(10): 257-276.
[8] 相超. 贴补复合材料层合板的静强度与稳定性研究[D]. 南京: 南京航空航天大学, 2014.
[9] F. Hashagen.Delamination behavior of spliced fiber metal laminates[J]. Composite Structures,1999(46): 131-145.
[10] FA Ghasemi, LM Vanani, AP Anaraki. A study on the charpy impact response of the cracked aluminum plates repaired with FML composite patches[J]. Journal of Failure Analysis & Prevention, 2016, 16(4): 594-600.
[11] AP Anaraki, GH Payganeh, FA Ghasemi, et al. An experimental study on the tensile behavior of the cracked aluminum plates repaired with FML composite patches[J]. World Academy of Science Engineering & Technology, 2013(14): 53-58.
[12] 王清远, 陶华. 复合材料修补件的强度和疲劳性能[J]. 材料工程, 2003(1): 21-23, 41.
[13] 付立华. 复合材料修补技术的研究[J]. 今日科苑,2009, 180(10): 57-58.
[14] 王清远, 袁祥明, 李戍中. 损伤金属结构件复合材料粘贴修补[J]. 玻璃钢/复合材料, 2003(6): 41-44.
[15] Po-Ching Yeh, Po-Yu Chang, Jenn-Ming Yang. Blunt notch strength of hybrid boron/glass/aluminum fiber metal laminates[J]. Material Science and Engineering, 2010(528): 2164-2173.