RTM多孔注射成型注射参数对树脂流动的影响规律研究

玻璃钢/复合材料 ›› 2019, Vol. 0 ›› Issue (12): 47-53.

RTM多孔注射成型注射参数对树脂流动的影响规律研究

向琳彤¹, 赵安安², 于飞², 鲁世红^1*

1.南京航空航天大学机电学院,南京210016;
2.西安飞机工业集团有限责任公司制造工程部,西安710089

收稿日期:2019-04-02 出版日期:2019-12-28 发布日期:2019-12-28
通讯作者: 鲁世红(1964-),女,博士,教授,主要从事先进复合材料成型、喷丸成型,超塑成型/扩散连接等方面的研究,lush@nuaa.edu.cn。
作者简介:向琳彤(1995-),女,硕士,主要研究方向为先进复合材料成型技术。

STUDY ON THE INFLUENCE OF INJECTION PARAMETERS ON RESIN FLOW IN RTM POROUS INJECTION MOLDING

XIANG Lin-tong¹, ZHAO An-an², YU Fei², LU Shi-hong^1*

1.Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;
2.Manafacture Engineering Department, Xi′an Aircraft Industry Group Co., Ltd., Xi′an 710089, China

Received:2019-04-02 Online:2019-12-28 Published:2019-12-28

摘要/Abstract

摘要： 采用树脂传递模塑工艺成型结构件时,为了提高制造效率,往往采用多注射口的方式进行成型。多注射口成型过程中注射口和排气口的位置、注射压力等工艺参数的选择会影响树脂的流动,进而影响最终成型件的质量。当前大型结构件以及复杂结构件往往用到多注射口成型方式,需要获得多注射口工艺注射参数对树脂流动的影响。利用Fluent仿真软件进行了数值模拟,采用控制变量法,研究了多注射口的数量、相邻注射口之间的距离及注射压力对树脂流动的影响,得到了上述三个注射参数与熔接痕长度和充模时间之间的关系。研究结果表明:充模时间和注射口的数量、相邻注射口之间的距离以及注射压力均成反比;熔接痕长度与注射口数量、注射口之间的距离成正比,与注射压力无关。

关键词: 树脂传递模塑成型, 多孔注射, 树脂流动, 数值模拟

Abstract: In order to improve the efficiency of resin transfer molding, porous injection molding is often used. In the process of porous injection molding, the location of injection and outlet, injection pressure and other process parameters will affect the flow of resin, and then affect the quality of final parts. At present, the porous injection molding is often used for large and complex structural parts, so it is necessary to obtain the influence of injection parameters on the resin flow. In this paper, based on the numerical simulation by Fluent software, the influence of the number of injections, the distance between adjacent injections and the injection pressure on the resin flow were analyzed by using the control variable method, and the relationship among the three parameters and the length of weld lines and filling time was obtained. The simulation results show that the filling time is inversely proportional to the number of injection ports, the distance between adjacent injection ports and the injection pressure, and the length of weld line is proportional to the number of injection ports and the distance between injections, and not related to injection pressure.

Key words: RTM, porous injection, resin flow, numerical simulation

中图分类号:

TB332

向琳彤, 赵安安, 于飞, 鲁世红. RTM多孔注射成型注射参数对树脂流动的影响规律研究[J]. 玻璃钢/复合材料, 2019, 0(12): 47-53.

XIANG Lin-tong, ZHAO An-an, YU Fei, LU Shi-hong. STUDY ON THE INFLUENCE OF INJECTION PARAMETERS ON RESIN FLOW IN RTM POROUS INJECTION MOLDING[J]. Fiber Reinforced Plastics/Composites, 2019, 0(12): 47-53.

参考文献

[1] Saad A, Echchelh A, Hattabi M. An optimized control volume/finite element method (CV/FEM) for non-isothermal liquid composite molding (LCM) process[J]. Thermo-Mechanics Applications and Engineering Technology, 2018, 2(1): 81-118.
[2] 拉德. 复合材料液体模塑成型技术[M]. 北京: 化学工业出版社, 2004.
[3] 王庆涛, 朱家强, 李炜. VARTM和RTM工艺模拟仿真比较[J]. 玻璃钢/复合材料, 2013(6): 12-15.
[4] Jiang S, Zhang C, Wang B. Optimum arrangement of gate and vent locations for RTM process design using a mesh distance-based approach[J]. Composites Part A, 2002, 33(4): 471-481.
[5] Matsuzaki R, Shiota M. Data assimilation through integration of stochastic resin flow simulation with visual observation during vacuum-assisted resin transfer molding: A numerical study[J]. Composites Part A, 2016, 84(5): 43-52.
[6] 齐文, 刘东, 赵俊利. RTM工艺充模过程模拟研究进展[J]. 玻璃钢/复合材料, 2015(12): 105-109.
[7] 冯武, 王继辉, 高国强. RTM多注射口成型的控制研究[J]. 武汉理工大学学报, 2005, 27(3): 19-22.
[8] 邹如荣, 柳和生, 赖家美. 一典型结构复合材料零件的VARTM注射方式优化及实验[J]. 玻璃钢/复合材料, 2015(12): 65-72.
[9] Okabe T, Oya Y, Yamamoto G, et al. Multi-objective optimization for resin transfer molding process[J]. Composites Part A Applied Science and Manufacturing, 2017, 92(1): 1-9.
[10] 陈吉平, 苏佳智, 韩小勇. 复合材料工型肋的RTM工艺模拟与优化[J]. 玻璃钢/复合材料, 2017(7): 82-87.
[11] Ye X, Yan S L. The simulation of the un-saturated flow in the dual-scale porous media under constant flow rate[J]. Advanced Materials Research, 2013(753-755): 2747-2751.
[12] Zhou Y F, Fang X, Wang W Q, et al. Numerical simulation of the influence of fibrous structure on resin filling in RTM process[J]. Journal of East China University of Science & Technology, 2017, 43(2): 162-170.
[13] 魏雅君, 朱豪磊, 卢洋洋. 基于VOF方法的RTM充模非饱和流动仿真算法研究[J]. 橡塑技术与装备, 2017, 43(10): 15-19.
[14] 张健, 方杰, 范波芹. VOF方法理论与应用综述[J]. 水利水电科技进展, 2005, 25(2): 67-70.
[15] 杨俊英, 贾玉玺, 丁妍羽. 基于VOF/PLIC界面追踪方法的RTM工艺充模过程数值模拟[J]. 材料研究学报, 2009, 23(6): 622-627.