碳纤维含量对增强尼龙复合材料性能的影响

玻璃钢/复合材料 ›› 2019, Vol. 0 ›› Issue (9): 64-68.

碳纤维含量对增强尼龙复合材料性能的影响

陈邑¹, 黄珍媛¹, 刘颖², 刘强^{2, 3*}

1.华南理工大学机械与汽车工程学院,广州510640;
2.中山大学智能工程学院,深圳518000;
3.广东省轻量化电动汽车及零配件开发中心,东莞523000

收稿日期:2018-11-06 出版日期:2019-09-28 发布日期:2019-09-28
通讯作者: 刘强(1981-),男,博士,副教授,主要从事轻量化复合材料结构开发方面的研究,Liu5168198110@126.com。
作者简介:陈邑(1995-),男,硕士研究生,主要从事新材料成型与仿真模拟技术方面的研究。
基金资助:
国家自然科学基金(51675540);东莞市科技计划项目(20185071551596)

EFFECT OF CARBON FIBER CONTENT ON PROPERTY OF REINFORCED NYLON COMPOSITE

CHEN Yi¹, HUANG Zhen-yuan¹, LIU Ying², LIU Qiang^2,3*

1.School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510610, China;
2.School of Intelligent Systems Engineering, Sun Yat-sen University, Shenzhen 518000, China;
3.Lightweight Electric Vehicle and Parts Engineering Center of Guangdong Province, Dongguan 523000, China

Received:2018-11-06 Online:2019-09-28 Published:2019-09-28

摘要/Abstract

摘要： 碳纤维可以提高工程塑料的力学性能,本文研究了碳纤维含量对碳纤维/PA66复合材料性能和增强效率的影响规律,并对其增强的原因进行了分析。采用注塑成型工艺制备了10wt%~40wt%纤维含量的碳纤维/PA66拉伸试样,通过试验获得了增强复合材料的弹性模量和抗拉强度,并与未增强样件进行了对比;分析了碳纤维含量对纤维增强效率的影响,采用扫描电子显微镜(SEM)观察了拉伸试样断面的微观结构。研究表明:碳纤维/PA66的弹性模量随着纤维含量的增加而增大,抗拉强度先增大后下降,峰值出现在纤维含量为30wt%时;碳纤维/PA66复合材料弹性模量的纤维增强效率受碳纤维含量的影响不大,高纤维含量下碳纤维对碳纤维/PA66复合材料抗拉强度的增强效率下降,主要是由于高纤维含量下微观界面强度的减弱和纤维接触概率增大导致的界面缺陷。本文研究的碳纤维含量对碳纤维/PA66材料力学性能和效率的影响规律,可为增强复合材料的设计提供指导。

关键词: 碳纤维, 尼龙66, 力学性能, 增强效率, 微观结构

Abstract: Carbon fiber can improve the mechanical properties of engineering plastics. This paper studies the effect of carbon fiber content on the properties and reinforced efficiency of carbon fiber reinforced nylon 66 (CF/PA66) composites, and analyzes the reasons for its enhancement. The CF/PA66 tensile specimens with fiber fraction of 10wt% to 40wt% were prepared by injection molding process. The elastic modulus and tensile strength of the reinforced composites were obtained through experiments and compared with the unreinforced samples. The effect of carbon fiber content on fiber-reinforced efficiency was analyzed. The fracture surface of tensile specimens was observed by scanning electron microscopy (SEM). The results show that the elastic modulus of CF/PA66 increases with the increase of fiber content, the tensile strength increases first and then decreases, and the peak value appears when the fiber content is 30wt%; the fiber-reinforced efficiency of CF/PA66 composites is not affected by carbon fiber content. The high fiber content of carbon fiber has lower tensile strength enhancement of CF/PA66 composites. The main reason is the weakening of micro-interface strength and the interface defect caused by the increase of fiber contact probability under high fiber content. The effect of the carbon fiber content studied on the reinforcing properties and efficiency of carbon fiber/PA66 materials can provide guidance for the design of reinforced composite materials.

Key words: carbon fiber, nylon 66, mechanical property, reinforced efficiency, microstructure

中图分类号:

TB332

陈邑, 黄珍媛, 刘颖, 刘强. 碳纤维含量对增强尼龙复合材料性能的影响[J]. 玻璃钢/复合材料, 2019, 0(9): 64-68.

CHEN Yi, HUANG Zhen-yuan, LIU Ying, LIU Qiang. EFFECT OF CARBON FIBER CONTENT ON PROPERTY OF REINFORCED NYLON COMPOSITE[J]. Fiber Reinforced Plastics/Composites, 2019, 0(9): 64-68.

参考文献

[1] Garcia-Gonzalez D, Rusinek A, Jankowiak T, et al. Mechanical impact behavior of polyether-ether-ketone (PEEK)[J]. Composite Structures, 2015, 124(Supplement C): 88-99.
[2] Nash N H, Young T M, Mcgrail P T, et al. Inclusion of a thermoplastic phase to improve impact and post-impact performances of carbon fibre reinforced thermosetting composites-A review[J]. Materials & Design, 2015, 85: 582-597.
[3] 李伟, 钱秀洋, 费又庆. 短切碳纤维增强尼龙66复合材料注塑成型工艺模拟[J]. 复合材料学报, 2017, 34(4): 812-818.
[4] 张其, 王孝军, 张刚, 等. 碳纤维增强尼龙PA6T/66共聚物复合材料的制备及性能研究[J]. 塑料工业, 2015, 43(4): 124-126.
[5] Kobayashi D, Hsieh Y T, Takahara A. Interphase structure of carbon fiber reinforced polyamide 6 revealed by microbeam X-ray diffraction with synchrotron radiation[J]. Polymer, 2016, 89: 154-158.
[6] Chen H, Cieslinski M, Baird D G. Progress in modeling long glass and carbon fiber breakage during injection molding[C]//AIP Conference Proceedings. AIP Publishing LLC, 2015.
[7] Kawai M, Takeuchi H, Taketa I, et al. Effects of temperature and stress ratio on fatigue life of injection molded short carbon fiber-rein-forced polyamide composite[J]. Composites Part A: Applied Science and Manufacturing, 2017, 98: 9-24.
[8] Tseng H, Chang R, Hsu C H. Improved fiber orientation predictions for injection molded fiber composites[J]. Composites Part A: Applied Science and Manufacturing, 2017, 99: 65-75.
[9] Magniez K, Iftikhar R, Fox B L. Properties of bio-based polymer nylon 11 reinforced with short carbon fiber composites[J]. Polymer Composites, 2015, 36(4): 668-674.
[10] Chen H, Cai Q, Wu J, et al. Interfacial enhancement of carbon fiber/nylon 12 composites by grafting nylon 6 to the surface of carbon fiber[J]. Applied Surface Science, 2018, 441: 538-545.
[11] 孙伟, 宋国君, 杨淑静, 等. 双螺杆反应挤出制备碳纤维增强尼龙6复合材料的研究[J]. 科学技术与工程, 2009, 9(3): 620-623.
[12] 甘舟, 曹海琳, 晏义伍, 等. 碳纤维-Ni/尼龙66复合材料的制备与性能表征[J]. 复合材料学报, 2017, 34(5): 945-951.
[13] Capela C, Oliveira S E, Pestana J, et al. Effect of fiber length on the mechanical properties of high dosage carbon reinforced[J]. Procedia Structural Integrity, 2017(5): 539-546.
[14] Fu S Y, Lauke B, Mäder E, et al. Tensile properties of short-glass-fiber-and short-carbon-fiber-reinforced polypropylene composites[J]. Composites Part A: Applied Science and Manufacturing, 2000, 31(10): 1117-1125.
[15] Houshyar S, Shanks R A, Hodzic A. The effect of fiber concentration on mechanical and thermal properties of fiber-reinforced polypropylene composites[J]. Journal of Applied Polymer Science, 2005, 96(6): 2260-2272.
[16] Unterweger C, Duchoslav J, Stifter D, et al. Characterization of carbon fiber surfaces and their impact on the mechanical properties of short carbon fiber reinforced polypropylene composites[J]. Composites Science and Technology, 2015, 108 (Supplement C): 41-47.