短切碳纤维增强塑料纤维分布的精细化表征

复合材料科学与工程 ›› 2020, Vol. 0 ›› Issue (3): 26-30.

短切碳纤维增强塑料纤维分布的精细化表征

黄珍媛, 程斌, 赵亚萌, 陈邑

华南理工大学机械与汽车工程学院,广州510640

收稿日期:2019-07-25 出版日期:2020-03-28 发布日期:2020-03-28
作者简介:黄珍媛(1975-),女,副教授,博士,主要从事新材料成型与模拟分析技术研究,zhenyuan@scut.edu.cn。
基金资助:
国家自然科学基金(51675540);东莞市科技计划项目(20185071551596)

FINE CHARACTERIZATION OF THE FIBER DISTRIBUTION OF SHORT CARBON FIBER REINFORCED PLASTIC

HUANG Zhen-yuan, CHENG Bin, ZHAO Ya-meng, CHEN Yi

School of Mechanical and Automotive Engineering, South China University of Technology,Guangzhou 510610, China

Received:2019-07-25 Online:2020-03-28 Published:2020-03-28

摘要/Abstract

摘要： 碳纤维增强塑料是近几年新兴的优质轻质材料,具有较好的力学性能,被广泛应用于汽车、电子等行业中。短切碳纤维增强塑料通常采用注塑成型工艺,其性能与纤维分布有着密切的关系。为了加深对短切碳纤维增强注塑件内部纤维分布规律的了解,开展SEM和X射线断层扫描试验,结合图像处理技术得到纤维拔出孔直径、流动平面纤维投影长度以及纤维取向分布规律,并与Moldex模拟结果对比,进一步验证纤维取向分布的规律。结果表明:碳纤维增强塑料成型后纤维拔出孔直径的分布受纤维含量的影响不大;纤维取向整体朝向为流动方向,沿流动方向的取向概率随平面到芯层距离的减小先增大后下降;碳纤维增强塑料注塑成型时,沿流动方向取向比例较高的区域均为位于皮层和芯层的中间区域。

关键词: 碳纤维增强塑料, 纤维分布, 流动方向, 表征

Abstract: Carbon fiber reinforced plastic is a new high-quality lightweight material in recent years. It has good mechanical properties and is widely used in the automotive, electronics and other industries. Short carbon fiber reinforced plastics are usually injection molded and their properties are closely related to fiber distribution. In order to deepen the understanding of the internal fiber distribution of staple fiber carbon fiber reinforced plastics, SEM and X-ray tomography tests were carried out. The fiber extraction hole diameter, the projected length of the flow plane fiber and the distribution of fiber orientation were obtained by image processing technology, and the law of fiber orientation distribution was further verified by comparison with the Moldex simulation results. The results show that the fiber extraction hole diameter distribution of carbon fiber reinforced plastics is not affected by the fiber content. The overall orientation of fiber orientation is the flow direction, and the orientation probability along the flow direction increases first and then decreases with the decrease of the distance from the plane to the core layer. In the case of carbon fiber reinforced plastic injection molding, the areas with a higher orientation ratio in the flow direction are located in the middle of the skin layer and the core layer.

Key words: carbon fiber reinforced plastics, fiber distribution, flow direction, characterization

中图分类号:

TB332

黄珍媛, 程斌, 赵亚萌, 陈邑. 短切碳纤维增强塑料纤维分布的精细化表征[J]. 复合材料科学与工程, 2020, 0(3): 26-30.

HUANG Zhen-yuan, CHENG Bin, ZHAO Ya-meng, CHEN Yi. FINE CHARACTERIZATION OF THE FIBER DISTRIBUTION OF SHORT CARBON FIBER REINFORCED PLASTIC[J]. Composites Science and Engineering, 2020, 0(3): 26-30.

参考文献

[1] Aoki Y, Yamada K, Ishikawa T. Effect of hygrothermal condition on compression after impact strength of CFRP laminates. Composites Science & Technology, 2008, 68(6): 1376-1383.
[2] Suvarna R, Arumugam V, Bull D J, et al. Effect of temperature on low velocity impact damage and post-impact flexural strength of CFRP assessed using ultrasonic C-scan and micro-focus computed tomography. Composites Part B, 2014, 66(4): 58-64.
[3] Soutis C. Fibre reinforced composites in aircraft construction. Progress in Aerospace Sciences, 2005, 41(2): 143-151.
[4] Press E. Measuring spatial orientation of short fiber reinforced thermoplastics by image analysis. Polymer Composites, 2010, 9(4): 297-304.
[5] Mlekusch B. Fibre orientation in short-fibre-reinforced thermoplastics Ⅱ. Quantitative measurements by image analysis. Composites Science and Technology, 1999, 59(4): 547-560.
[6] 袁海兵. 短切碳纤维增强聚丙烯复合材料的性能. 合成树脂及塑料, 2018, 35(2): 24-28.
[7] 郑开宏, 高积强. 纤维长度、取向对LAS基体力学性能的影响. 无机材料学报, 1997, 12(2): 143-148.
[8] 武玉芬, 张博明. 碳纤维拉伸强度的离散性分析. 玻璃钢/复合材料, 2010(3): 29-31.
[9] Bernasconi A, Cosmi F, Hine P J. Analysis of fibre orientation distribution in short fibre reinforced polymers: A comparison between optical and tomographic methods. Composites Science & Technology, 2012, 72(16): 2002-2008.
[10] Urabe K, Yomoda S. A nondestructive testing method of fiber orientation by microwave. Advanced Composite Materials, 1991, 1(3): 193-208.
[11] Desplentere F, Lomov S V, Woerdeman D L, et al. Micro-CT characterization of variability in 3D textile architecture. Composites Science and Technology, 2005, 65(13): 1920-1930.
[12] Joffre T, Miettinen A, Berthold F, et al. X-ray micro-computed tomography investigation of fibre length degradation during the processing steps of short-fibre composites. Composites Science and Technology, 2014, 105: 127-133.
[13] Jin K, Youn J R. Prediction of fiber orientation in the thickness plane during flow molding of short fiber composites. Polymer Composites, 2010, 16(2): 114-124.
[14] 郭胜立, 卢关涛, 孔令超, 等. 注射成型纤维取向模拟及实验验证. 工程塑料应用, 2011, 39(7): 31-34.
[15] Oumer A N, Hamidi N M, Sahat I M. Numerical prediction of flow induced fibers orientation in injection molded polymer composites//Materials Science & Engineering Conference Series. Materials Science and Engineering Conference Series, 2015.