温度和圆孔缺陷对层合板线性屈曲特性的影响分析

复合材料科学与工程 ›› 2021, Vol. 0 ›› Issue (2): 77-83.

温度和圆孔缺陷对层合板线性屈曲特性的影响分析

苏君^1,2, 孔琳³, 夏志平^4*

1.河南工业职业技术学院机械工程学院,南阳473009;
2.河南省材料成形装备智能技术工程研究中心,南阳473009;
3.南阳技师学院,南阳473000;
4.九江职业技术学院机械工程学院,九江332007

收稿日期:2020-06-11 出版日期:2021-02-28 发布日期:2021-03-10
通讯作者: 夏志平(1988-),男,硕士,讲师,主要从事机械设计与材料成型方面的研究。
作者简介:苏君(1977-),女,硕士,副教授,主要从事材料成型方面的研究。
基金资助:
2018年河南省科技发展计划(182102210266)

THE INFLUENCE ANALYSIS OF TEMPERATURE AND CIRCULAR-HOLE DEFECT
ON THE LINEAR BUCKLING OF LAMINATED PLATE

SU Jun^1,2, KONG Lin³, XIA Zhi-ping^4*

1. School of Mechanical Engineering, Henan Polytechnic Institute, Nanyang 473009, China;
2. Henan Material Forming Equipment Intelligent Technology Engineering Research Center, Nanyang 473009, China;
3. Nanyang Technician College, Nanyang 473000, China;
4. School of Mechanical Engineering, Jiujiang Vocational and Technical College, Jiujiang 332007, China

Received:2020-06-11 Online:2021-02-28 Published:2021-03-10

摘要/Abstract

摘要： 随着应用环境趋于复杂,层合板经常会处于不同的温度环境以及经常需要开圆孔进行机械连接,且厚度方向尺寸较小,受压缩时容易发生屈曲现象,因此,研究不同温度和圆孔缺陷对层合板屈曲特性的影响具有重要的意义。首先对欧拉梁理论进行简单回顾,推导出梁在两端铰接受压状态时的平衡载荷和挠曲线的解析解。进一步用有限元方法对各向同性板屈曲问题进行研究,将屈曲载荷和屈曲模态与基于欧拉梁理论的解析解进行对照,确定合适的网格密度,验证模型的正确性。然后对含不同圆孔尺寸的准各向同性层合板在不同温度下进行屈曲特性分析,分别得到前五阶的屈曲载荷和屈曲模态。最后研究了不同圆孔尺寸下,圆孔深度对层合板屈曲特性的影响。结果表明:随着温度的升高,含相同圆孔尺寸的层合板的屈曲载荷线性下降;同一温度下,随着圆孔尺寸的增大,屈曲载荷下降越来越快;同一圆孔尺寸下,随着圆孔深度的增加,屈曲载荷下降速度先减小后增大,呈现出对称性。

关键词: 温度, 圆孔缺陷, 层合板, 屈曲载荷, 屈曲模态, 复合材料

Abstract: With the application environment of laminated plates becoming more and more complex, they are often in different temperature environment and often need to drill a circular-hole for mechanical connection, and the size of thickness direction is small, so they are prone to buckling when compressed. Therefore, it is of great significance to study the effects of different temperatures and circular-hole defects on the buckling characteristics of laminated plates. Firstly, the theory of Euler beam is reviewed, and the analytical solutions of the equilibrium load and deflection curve of the beam under the condition of hinged compression at both ends are derived. Furthermore, the finite element method is used to study the buckling problem of isotropic plates. The buckling load and buckling mode are compared with the analytical solution based on the Euler beam theory to determine the appropriate mesh density and verify the correctness of the model. Then, the buckling characteristics of quasi-isotropic laminated plates with different circular-hole sizes are analyzed at different temperature levels, and the first five buckling loads and modes are obtained respectively. Finally, the effect of the depth of the circular-hole on the buckling behavior of the laminated plate is studied. The results show that with the increment of temperature, the buckling load of laminated plates with the same hole size decreases linearly. With the increment of the circular-hole size at the same temperature, the buckling load decreases faster and faster; with the increment of the hole depth at the same circular-hole size, the buckling load decreases firstly and then increases, showing symmetry.

Key words: temperature, circular-hole defect, laminate, buckling load, buckling mode, composites

中图分类号:

TB332

苏君, 孔琳, 夏志平. 温度和圆孔缺陷对层合板线性屈曲特性的影响分析[J]. 复合材料科学与工程, 2021, 0(2): 77-83.

SU Jun, KONG Lin, XIA Zhi-ping. THE INFLUENCE ANALYSIS OF TEMPERATURE AND CIRCULAR-HOLE DEFECT
ON THE LINEAR BUCKLING OF LAMINATED PLATE[J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(2): 77-83.

参考文献

[1] PARK H J. Effects of stacking sequence and clamping force on the bearing strengths of mechanically fastened joints in composite laminates[J]. Composite Structures, 2001(53): 213-221.
[2] 朱建辉, 曾建江, 陈滨琦, 等. 复合材料层合板压缩载荷下渐进损伤分析与试验验证[J]. 机械科学与技术, 2015(5): 785-789.
[3] LEE Y G, CHOI E, YOON S J. Effect of geometric parameters on the mechanical behavior of PFRP single bolted connection[J]. Composite Part B: Engineering, 2015(75): 1-10.
[4] MCCARTHY M, LAWLOR V, STANLEY W, et al. Bolt hole clearance effects and strength criteria in single-bolt, single lap, composite bolted joints[J]. Composite Science and Technology, 2002(62): 1415-1431.
[5] MOITA J S, MOTA SOARES C M, SOARES C A M. Buckling and dynamic behaviour of laminated composite structures using a discrete higher-order displacement model[J]. Computers and Structures, 1999(73): 407-423.
[6] MOITA J S, BARBOSA J I, MOTA SOARES C M, et al. Sensitivity analysis and optimal design of geometric nonlinear laminated plates and shells[J]. Computers and Structures, 2000(76): 407-420.
[7] MOITA J S, ARAÚJO A L, CORREIA V F, et al. Buckling and nonlinear response of functionally graded plates under thermo-mechanical loading[J]. Composite Structures, 2018(202): 719-730.
[8] MOITA J S, ARAÚJO A L, CORREIA V F, et al. Buckling behavior of composite and functionally graded material plates[J]. European Journal of Mechanics/A Solids, 2020(80): 103921.
[9] HAFFAR M Z, SANDOR A. On the buckling of longitudinally stiffened plates, part 1: Modal analysis by the constrained finite element method[J]. Thin-walled structures, 2019(145): 106394.
[10] 张建, 周通, 王纬波, 等. 模态缺陷条件下复合材料柱形壳屈曲特性[J]. 复合材料学报, 2017, 34(3): 588-596.
[11] 刘洪权, 谭申刚, 张建刚, 等. 几何缺陷对复合材料加筋平板轴压屈曲影响研究[J]. 机械科学与技术, 2018, 37(12): 1963-1968.
[12] 朱秀杰, 熊超, 尹德军, 等. 基于薄板小挠度理论计算复合材料矩形薄壁管局部屈曲载荷[J]. 玻璃钢/复合材料, 2019(11): 30-36.
[13] LANHE W. Thermal buckling of a simply supported moderately thick rectangular FGM plate[J]. Composite Structures, 2004, 64(2): 211-218.
[14] 庄茁, 由小川, 廖剑晖, 等. 基于ABAQUS的有限元分析和应用 [M]. 北京: 清华大学出版社, 2009.
[15] CZEL G, REV T, JALALVAND M, et al. Pseudo-ductility and reduced notch sensitivity in multi-directional all-carbon/epoxy thin-ply hybrid composites[J]. Composites Part A: Applied Science and Manufacturing, 2018, 104: 151-164.
[16] ZHANG J, QI D, ZHOU L, et al. A progressive failure analysis model for composite structures in hygrothermal environments[J]. Composite Structures, 2015, 133: 331-342.
[17] BENKHEDDA A, TOUNSI A. Effect of temperature and humidity on transient hygrothermal stresses during moisture desorption in laminated composite plates[J]. Composite Structures, 2008, 82(4): 629-635.