胶接对碳纤维层合板与铝合金板单钉连接静强度的影响

doi:10.19936/j.cnki.2096-8000.20221228.006

摘要/Abstract

摘要： 开展了碳纤维层合板与铝合金板单钉连接及胶螺连接静强度拉伸实验。建立了胶螺连接有限元模型,编写子程序将三维Hashin失效准则嵌入了计算模型。对板间胶层脱黏机理进行了研究,分析了碳纤维层合板的渐进损伤过程。基于实验数据对数值计算模型进行了修正。修正后有限元模型的峰值载荷与实验值误差为2.9%,二次峰值误差为14.8%。研究表明:高强度胶黏剂能提高单钉胶螺连接结构强度和安全裕度;胶黏剂强度越高则峰值载荷越高;板间胶层脱黏后,载荷二次峰值低于初始峰值,且与无胶接单钉螺栓连接峰值载荷基本吻合;螺栓孔内注胶的胶螺连接结构的连接刚度和稳定性优于孔内无胶连接结构;本文构建的有限元模型能较准确模拟位移加载下板间胶层的脱黏机理和碳纤维层合板的渐进损伤过程。

关键词: 胶接, 碳纤维, 层合板, 连接, 强度

Abstract: The static strength tensile tests of single-bolted joint and bonded-bolted joint of carbon fiber laminate and aluminum alloy plate are carried out. A finite element model of the bonded-bolted joint is established. The three-dimensional Hashin failure criterion is embedded in the analysis model by subroutine programming. The debonding mechanism of the adhesive layer between the laminate and aluminum plate is studied, and the failure evolution process of the carbon fiber laminates is analyzed. The numerical model is revised based on test data. After the correction, the peak load error between the finite element model and the test value is 2.9%, and the error of the second peak is 14.8%. It is showed that high-strength adhesive improves the joint strength and expands safety margin of the single-bolted and bonded joint. The higher the adhesive strength, the higher the peak load. When the debonding occurs between the laminate and aluminum plate, the secondary peak load is lower than the initial one. The secondary peak load is consistent with the peak load of the non-adhesive single-bolted joint. The joint stiffness and stability of the bonded-bolted joint with adhesive in the bolt hole is better than that of the joint without adhesive in the bolt hole. The debonding mechanism of the adhesive layer between the laminate and aluminum plate under displacement loading and the failure evolution process of carbon fiber laminates are simulated well by the finite element model established in this paper.

Key words: bonding, carbon fiber, laminate, joint, strength

中图分类号:

TB332

刘峰, 王卓煜, 豆广征. 胶接对碳纤维层合板与铝合金板单钉连接静强度的影响[J]. 复合材料科学与工程, 2022, 0(12): 46-53.

LIU Feng, WANG Zhuo-yu, DOU Guang-zheng. Bonding influence on static strength of single bolted joint of carbon laminates and aluminum alloy plate[J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(12): 46-53.

参考文献

[1] HART S. Bonded-bolted composite joints[J]. Journal of Aircraft, 1985, 22(11): 993-1000.
[2] KWEON J, JUNG J, KIM T, et al. Failure of carbon composite-to-aluminum joints with combined mechanical fastening and adhesive bonding[J]. Composite Structures, 2006, 75(1-4): 192-198.
[3] FARUK S, MURAT P, ONUR S, et al. Experimental failure analysis of mechanically fastened joints with clearance in composite laminates under preload[J]. Materials and Design, 2007, 29(6): 1159-1169.
[4] SEONG M, KIM T, NGUYEN K, et al. A parametric study on the failure of bonded single-lap joints of carbon composite and aluminum[J]. Composite Structures, 2008, 86(1-3): 135-145.
[5] LOPEZ C, LALIBERTE J, LESSARD L. Investigation of bolted/bonded composite joint behaviour using design of experiments[J]. Composite Structures, 2017, 170: 192-201.
[6] NOSOUHI F, FARAHANI M, ANSARI M. Experimental and numerical study on the composite adhesive joint reinforcement using wavy edge[J]. Journal of Adhesion Science and Technology, 2018, 32(9): 1007-1017.
[7] RIBEIRO T, CAMPILHO R, SILVA L, et al. Damage analysis of composite aluminium adhesively bonded single-lap joints[J]. Composite Structures, 2016, 13: 25-33.
[8] SULU I. Mechanical behavior of single-lap and do composite aircraft structures[C]//Journal of Physics: Conference Series. IOP Publishing. 2021, 1925(1): 012070.
[9] WEI K, CHEN Y, LI M, et al. Strength and failure mechanism of composite-steel adhesive bond single lap joints[J]. Advances in Materials Science and Engineering, 2018, 5810180.
[10] AKPINAR I , GULTEKIN K, AKPINAR S, et al. Research on strength of nanocomposite adhesively bonded composite joints[J]. Composites Part B: Engineering, 2017, 126: 143-152.
[11] HIZAM R, MANALO A, KARUNASENA W, et al. Effect of bolt threads on the double lap joint strength of pultruded fibre reinforced polymer composite materials[J]. Construction and Building Materials, 2018, 181: 185-198.
[12] 陈向明, 柴亚南, 袁菲, 等.胶-螺混合连接结构的传力分析[J]. 机械强度, 2017, 39(3): 668-673.
[13] ZAROUG M, KADIOGLU F, DEMIRAL M, et al. Experimental and numerical investigation into strength of bolted, bonded and hybrid single lap joints: Effects of adherend material type and thickness[J]. International Journal of Adhesion and Adhesives, 2018, 87: 130-141.
[14] 刘钧天. 复合材料胶接质量和胶接面性质研究[D]. 上海: 东华大学, 2018.
[15] SHANG X, MARQUES E A S, MACHADO J, et al. Review on techniques to improve the strength of adhesive joints with composite adherends[J]. Composites Part B: Engineering, 2019, 177: 107363.
[16] RUDAWSKA A. Comparison of the adhesive joints′ strength of the similar and dissimilar systems of metal alloy/polymer composite[J]. Applied Adhesion Science, 2019, 7(1): 1-17.
[17] YANG G, YANG T, YUAN W, et al. The influence of surface treatment on the tensile properties of carbon fiber-reinforced epoxy composites-bonded joints[J]. Composites Part B: Engineering, 2019, 160: 446-456.
[18] 毛振刚. 胶接参数对CFRP层合板胶接结构连接性能的影响研究[D]. 郑州: 郑州大学, 2020.
[19] KOSTIN V, NASONOV F, ZININ A. Influence of adhesive bond line thickness on joint strength of Mechanical characterization of a flexible epoxy adhesive for the design of hybrid bonded-bolted joints[J]. Polymer Testing, 2019, 79: 106048.
[20] LIM G, HEIDARI R, BODJONA K, et al. uble-lap adhesive joined composite parts[J]. Materials Testing, 2017, 59(11-12): 1019-1026.
[21] RAYKHERE S, KUMAR P, SINGH R, et al. Dynamic shear strength of adhesive joints made of metallic and composite adherents[J]. Materials & Design, 2010, 31(4): 2102-2109.
[22] HANUMANTHARAYA R, SOGALAD I, BASAVARAJAPPA S, et al. Modelling and optimisation of adhesive bonded joint strength of composites for aerospace applications[J]. International Journal of Computational Materials Science and Surface Engineering, 2019, 8(3-4): 167-184.
[23] 谢鸣九. 复合材料连接[M]. 上海: 上海交通大学出版社, 2011: 240-241.
[24] 刘峰, 王坤, 周建国, 等. 拧紧力矩对复合材料层合板与金属板连接强度影响[J]. 空军工程大学学报(自然科学版), 2020, 21(6): 13-18.
[25] CAMPILHO R D S G, BANEA M D, NETO J, et al. Modelling adhesive joints with cohesive zone models: effect of the cohesive law shape of the adhesive layer[J]. International Journal of Adhesion and Adhesives, 2013, 44: 48-56.
[26] HASHIN Z. Fatigue failure criteria for unidirectional fiber composites[J]. Journal of Applied Mechanics, 1981, 48(4): 846-852.
[27] CHANG F, SCOTT R, Springer G S. Strength of mechanically fastened composite joints[J]. Journal of Composite Materials, 1982, 16(6): 470-494.
[28] ABAQUS-Inc. Abaqus 6. 14 Analysis User′s Manual Volume V: Prescribed Conditions,Constraints & Interactions[R]. Rhode Island,USA: Hibbett,Karlsson and Sorensen Inc., 2011: 35. 1. 10.
[29] BENZEGGAGH M, KENANE M. Measurement of mixed-mode delamination fracture toughness of unidirectional glass/epoxy composites with mixed-mode bending apparatus[J]. Composites Science and Technology, 1996, 56(4): 439-449.
[30] 刘峰, 陈威杨, 周建国, 等. 混杂复合材料口盖机械冲击破坏机理研究[J]. 兵器装备工程学报, 2021, 42(9): 264-272.
[31] 华明建, 李春志, 王鸿渐. 微观组织对7075铝合金的屈服强度和抗应力腐蚀性能的影响[J]. 金属学报, 1988(1): 41-46.