激光辐照碳纤维复合材料的光学行为与仿真

玻璃钢/复合材料 ›› 2019, Vol. 0 ›› Issue (8): 72-77.

激光辐照碳纤维复合材料的光学行为与仿真

朱文凯,还大军,肖军^*,王武强

南京航空航天大学材料科学与技术学院,南京210016

收稿日期:2018-11-07 出版日期:2019-08-28 发布日期:2019-08-28
通讯作者: 肖军(1959-) ,男,硕士,教授,主要从事先进复合材料成型技术方面的研究,j.xiao@nuaa.edu.cn。
作者简介:朱文凯(1995-),男,硕士,主要从事复合材料成型工艺方面的研究。
基金资助:
国家重点基础研究发展计划(2014CB046501);江苏高校优势学科建设工程

OPTICAL BEHAVIOR AND SIMULATION OF LASER IRRADIATED CARBON FIBER COMPOSITES

ZHU Wen-kai, HUAN Da-jun, XIAO Jun^*, WANG Wu-qiang

College of Material Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Received:2018-11-07 Online:2019-08-28 Published:2019-08-28

摘要/Abstract

摘要： 为了研究激光辐照碳纤维复合材料的光学行为,采用碳纤维增强聚醚醚酮复合材料(CF/PEEK)作为试验样品,通过积分球实验测量样品随波长和入射角变化的反射率;进行了激光束反射实验,观察宏观反射图案随光线入射角和样品偏角的变化行为;对激光与样品间的微观行为进行分析,并通过光学设计软件对反射过程进行模拟仿真。积分球实验表明,样品反射率随波长的增加而变大,随入射角的增大而变小。宏观反射实验表明,光线入射角和样品偏角对反射图案均有较大影响,反射行为主要受表层纤维的镜面反射支配,而且模拟结果与试验结果基本一致。基于菲涅尔方程,根据最小二乘法拟合的样品有效折射率为n=2.26。

关键词: 碳纤维复合材料, 激光加工, CF/PEEK, 积分球实验, 反射率, 有效折射率, 模拟仿真

Abstract: In this study, the carbon fiber reinforced polyetheretherketone composite (CF/PEEK) was used as a test sample to study the optical behavior of laser irradiated carbon fiber composites. The reflectance of the sample as a function of wavelength and angle of incidence was measured by an integrating sphere experiment. A laser beam reflection experiment was carried out to observe the behavior of the macroscopic reflection pattern as a function of the incident angle of the light and the angle of the sample. The microscopic behavior between the laser and the sample was analyzed, and the reflection process was simulated by optical design software. The integrating sphere experiment shows that the reflectance of the sample becomes larger as the wavelength increases, and becomes smaller as the incident angle increases. Macroscopic reflection experiment shows that the incident angle of light and the off-angle of the sample have a great influence on the reflection pattern. The reflection behavior is mainly dominated by the specular reflection of the surface fibers, and the simulation results are basically consistent with the experimental results. Based on the Fresnel equation, the effective refractive index of the sample fitted according to the least squares method is n=2.26.

Key words: carbon fiber composite, laser processing, CF/PEEK, integrating sphere experiment, reflectivity, effective refractive index, simulation

中图分类号:

TB332

朱文凯,还大军,肖军,王武强. 激光辐照碳纤维复合材料的光学行为与仿真[J]. 玻璃钢/复合材料, 2019, 0(8): 72-77.

ZHU Wen-kai, HUAN Da-jun, XIAO Jun, WANG Wu-qiang. OPTICAL BEHAVIOR AND SIMULATION OF LASER IRRADIATED CARBON FIBER COMPOSITES[J]. Fiber Reinforced Plastics/Composites, 2019, 0(8): 72-77.

参考文献

[1] Steyer M, Dubratz M, Schütte A, et al. Laser-assisted thermoplastic tape-laying systems[J]. JEC Composites Magazine, 2009(47): 39-41.
[2] Schledjewski R. Thermoplastic tape placement-insitu consolidation is reachable[J]. Plastics Rubber and Composites, 2009, 38(9-10): 379-386.
[3] 宋清华. 热塑性复合材料自动铺放过程温度场分析及构件性能研究[D]. 南京: 南京航空航天大学, 2016.
[4] Yang F, Pitchumani R. Nonisothermal healing and interlaminar bond strength evolution during thermoplastic matrix composites processing[J]. Polymer Composites, 2010, 24(2): 263-278.
[5] Yang F, Pitchumani R. Interlaminar contact development during thermoplastic fusion bonding[J]. Polymer Engineering & Science, 2010, 42(2): 424-438.
[6] 韩振宇, 李玥华, 富宏亚, 等. 热塑性复合材料纤维铺放工艺的研究进展[J]. 材料工程, 2012(2): 91-96.
[7] Stokesgriffin C, Matuszyk T, Compston P, et al. Modelling the automated tape placement of thermoplastic composites with in-situ consolidation[J]. Springer Berlin Heidelberg, 2012(4): 61-68.
[8] Tierney J, Gillespie J W. Modeling of heat transfer and void dynamics for the thermoplastic composite tow-placement process[J]. Journal of Composite Materials, 2003, 37(19): 1745-1768.
[9] Pitchumani R, RanganathanS, Don R C, et al. Analysis of transport phenomena governing interfacial bonding and void dynamics during thermoplastic tow-placement[J]. International Journal of Heat & Mass Transfer, 1996, 39(9): 1883-1897.
[10] Ranganathan S, Advani S G, Lamontia M A. A Non-isothermal process model for consolidation and void reduction during in-situ tow placement of thermoplastic composites[J]. Journal of Composite Materials, 1995, 29(8): 1040-1062.
[11] 韩振宇, 孙守政, 付云忠, 等. 热塑性FRP自动铺放成型缺陷的多尺度研究进展[J]. 材料工程, 2017, 45(7): 118-127.
[12] Tierney J J, Gillespie J W. Crystallization kinetics behavior of PEEK based composites exposed to high heating and cooling rates[J]. Composites Part A: Applied Science & Manufact, 2004, 35(5): 547-558.
[13] Sonmez F O, Hahn H T. Analysis of the on-line consolidation process in thermoplastic composite tape placement[J]. Journal of Thermoplastic Composite Materials, 1997, 10(6): 543-572.
[14] Grouve W J B. Weld strength of laser-assisted tape-placed thermoplastic composites[D]. Enschede, the Netherlands: University of Twente, 2012: 10-24.
[15] Stokes-Griffin C M, Compston P. Optical characterisation and modelling for oblique near-infrared laser heating of carbon fibre reinforced thermoplastic composites[J]. Optics & Lasers in Engineering, 2015, 72: 1-11.
[16] Stokes-Griffin C M, Compston P. A combined optical-thermal model for near-infrared laser heating of thermoplastic composites in an automated tape placement process[J]. Composites Part A, 2015, 75: 104-115.
[17] 于冬洋, 王续跃. 单层碳纤维复合材料激光多向切割的温度场模拟[J]. 激光与光电子学进展, 2017 (11): 252-260.
[18] 蒋翼, 陈根余, 周聪, 等. 碳纤维复合材料皮秒激光切割工艺研究[J]. 激光技术, 2017, 41(6): 821-825.
[19] Freitag C, Weber R, Graf T. Polarization dependence of laser interaction with carbon fibers and CFRP[J]. Optics Express, 2014, 22(2): 1474-1479.